532634

Peaq PTV552403 Manual

30
Zoom out
Zoom in
Previous page
1/249
Next page
EN 8
Initial setup
Initial setup involves selecting all the settings
required to be able to search for and store all the
analogue and digital channels you can receive.
Make sure that the television is switched on and
follow all the steps in turn specified hereafter.
Note: If the channel search retrieved only the
analogue channels it could be caused by poor
broadcasting and therefore is not covered
by manufacturer warranty. Manufacturers
cannot be held responsible for lack of or poor
broadcasting in some areas.
The first time you switch the set on, the Initial setup
wizard opens, which guides you through the initial
setup process. (Refer to Figure 1.)
1. Press
▲
/
▼
to select your language, then press
OK/
►
to enter the next step.
2. Press
▲
/
▼
to select your country, then press
OK/
►
to enter the next step.
Note: If you select France, you will have to enter
the Password setting menu here in order
to set a password. Use the alphanumeric
buttons to enter a four-digit number for
your password. (0000 is too simple to be
set as your password.) Re-enter the same
code to confirm the password. After that,
you will enter the next step automatically.
(In this step, you can only press
◄
to
return to the previous step.)
3. Press
▲
/
▼
to select your tuner mode
Antenna or
Cable or Satellite. (Note:
Satellite option may not be available for certain
models.)
- Select Antenna.
•PressOK/
►
to enter.
•SelectDigital & Analogue, Digital or
Analogue, then press OK/
►
.
•Press
▲
/
▼
to select Scan, then press OK/
►
to start the automatic search for all DVB-T
digital and/or analogue channels.
- Select Cable.
•PressOK/
►
to enter.
•SelectDigital & Analogue, Digital or
Analogue, then press OK/
►
.
•Press
▲
/
▼
to select Scan, then press OK/
►
to directly start your initial setup or enter
below step.
•Select Full if available to search for and
store all DVB-C digital and analogue
channels.
•Youmayselectanotheradvancedscan
mode if available (for example, Advanced ),
then configure the correct cable information
as described below. Use the alphanumeric
buttons to adjust the values for frequency,
symbol rate and network ID; use
◄
/
►
to
select a modulation mode.
•PressOK to start initial setup relating to all
DVB-C digital and analogue channels.
- Select
Satellite.
•PressOK/
►
to enter.
•Press
▲
/
▼
to select Scan, then press OK/
►
to enter the next step to configure proper
information relating to satellite and antenna.
•PressOK to start initial setup relating to all
satellite channels.
Note: To prevent the channel setup process from
being interrupted, wait for the message
indicating that the setup is complete.
4. Before starting the scanning, you can also select
Skip scan to skip the initial setup process.
5. During the setup, you can follow the hints
available at the bottom of the screen to return to
the previous step by pressing
◄
. Or press EXIT
to exit or interrupt the search halfway.
6. Once the automatic search ends, the set enters
the next step automatically. Press
▲
/
▼
to select
your location Shop or Home. Press OK/
►
to
confirm your selection and enter the last step.
7. - In this step, you can press OK to exit the initial
setup. The channels are arranged in a preset
order. If you wish to skip channels, modify the
preset order or rename channels, select
Setup > Organiser and press OK/
►
to enter.
- In this step, you can also press
◄
to return to
the previous step.
Performing an automatic channel search
This section describes how to search and store
channels automatically. Instructions are for both
analogue and digital channels.
1. Press MENU on the remote control and select
Setup > Language > Menu language. Press
◄
/
►
to select your desired menu language.
2. Press MENU to return to Setup, press
▲
/
▼
to
select Country, then press
◄
/
►
to select your
country. The TV installs and arranges channels
according to your country.
3. Press
▲
/
▼
to select Tuner mode, then press
◄
/
►
to select
Antenna, Cable or
Satellite. (Note: Satellite option may not be
available for certain models.)
- Select
Antenna.
•Press
▲
/
▼
to select Channel install, and
press OK/
►
to enter.
•SelectAutomatic search (Refer to Figure 2.),
then press OK/
►
to display Automatic
search.
•PressOK to skip the country selection and
enter the next step. Or use
◄
/
►
to reselect
your country, then press OK to enter.
Installing channels Chapter 3
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Peaq PTV552403 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Peaq PTV552403 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 13,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info