689715
9
Zoom out
Zoom in
Previous page
1/10
Next page
11
GB/IE/CY
Q
Attaching the guide fence
The guide fence
19
can be attached on the left or
right side of the device (see Fig. A).
j Release the two locking screws of the fence
guide openings
15
.
j Slide the guide fence
19
into the fence guide
openings
15
.
j Retighten the two locking screws.
Q
Connecting the vacuum
sawdust extraction device
j Insert the dust extraction spout
7
into the
vacuum extraction duct
8
until it engages.
j Connect a vacuum device approved for the
extraction of sawdust and splinters to the dust
extraction spout
7
(see Fig. C).
Q
Operation
Q
Setting the cutting angle
j Release the clamp screw
11
using the Allen
key
20
.
j Set the cutting angle 0° / 15° / 30° / 45°
(left / right) on the base plate
9
. The embossed
marking for each recessed line indicates the
cutting angle setting. The housing has a stop
pin
21
(see Fig. B) which must engage in the
appropriate recessed line.
j Tighten the clamp screw
11
using the Allen
key
20
.
Q
Setting the speed
j Set the desired speed using the oscillation
speed setting wheel
4
.
j If possible always determine the optimum
setting beforehand by carrying out a
practical test.
Q
Setting the pendulum action
You can set the pendulum movement of the saw
blade
14
using the pendulum action switch
12
. By
having no pendulum action (setting “0”) you can
produce fine, clean cut edges. Turn off the
pendulum action for thin workpieces.
With the pendulum action activated (settings 1 3)
you can cut through the workpiece at increasingly
quicker rates.
j If possible always determine the optimum set-
ting beforehand using a practical test.
Q
Switching On / Off
c DANGER! Before connecting to the mains
plug check that the mains circuit supplies
230 V
~
50 Hz and is fitted with a 16 A fuse or
cut-out in accordance with the regulations!
Switching on:
j Push the ON / OFF switch
2
into position “I”
and ensure it engages.
Switching off:
j Press the rear part of the ON / OFF switch
2
.
Preparing for use / Operation
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PPHSS 730 - KH 3128 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PPHSS 730 - KH 3128 in the language / languages: English as an attachment in your email.

The manual is 2,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PPHSS 730 - KH 3128

Parkside PPHSS 730 - KH 3128 User Manual - German, Dutch, French - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info