595411
30
Zoom out
Zoom in
Previous page
1/34
Next page
27
PDMS A1
GB
Initial operation
NOTE
The grinder may only be operated on
cleaned, oil-atomised compressed air and
may not exceed the maximum operating
pressure of 6.3 bar at the appliance. The
compressor must be fi tted with a pressure
reducer to regulate the working pressure.
Wind the Tefl on tape supplied around all
threaded connectors.
Connect the appliance to a suitable compressed
air source.
First screw the 1/4“ threaded nipple onto
the mini compressed air oiler 1/4“ threaded
connector .
Then fi ll the mini compressed air oiler with
1-2 drops of special compressed air oil. To
do this, undo the crosshead screw at the mini
compressed air oiler
oil fi ller opening
and allow a few drops of oil to enter the oil
ller opening with the help of the oil bottle
included in delivery.
NOTE
A mist oiler continuously and optimally lubri-
cates the grinder as a preparation stage
after the pressure reducer. A mist oiler adds
ne drops of oil to air fl owing through the
appliance and therefore guarantees regular
lubrication.
Now screw the 1/4“ threaded nipple onto
the mini compressed air oiler 1/4“ female
threaded connector .
Now press the quick connector on the compressed
air hose (not included in delivery) onto the Com-
pressed air connector plug . The connection
locks automatically.
Now connect the other end of the compressed
air hose to the (fi lter) pressure reducer on the
compressor.
Tool-changing
Always disconnect the grinder from the compressed
air supply before changing tools.
Only ever use tools which are ready for use.
Furthermore, you must ensure that the minimum
clamping length of the shaft in the chuck is not
fallen below.
Using the spanners included in the accessories,
hold the spindle and chuck rmly and open
or close the chuck in the direction of the
arrows (see Fig. 3).
Fig. 3
Now insert one of the 10 diff erent whetstones .
NOTE
Please note the danger caused by mismatching
the diameter of the grinding tool shaft and
the chuck. Incorrectly-fi xed grinding tools can
cause severe vibration - injury hazard!
Ensure that the grinding tool is correctly fi xed,
and carry out a trial run of 30 seconds in a
safe area at idling speed.
OPEN
CLOSE
IB_43105_PDMSA1_LB1.indb 27IB_43105_PDMSA1_LB1.indb 27 14.05.14 11:1314.05.14 11:13
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PDMS A1 - IAN 43105 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PDMS A1 - IAN 43105 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PDMS A1 - IAN 43105

Parkside PDMS A1 - IAN 43105 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info