607092

Parkside PABS 10.8 B2 - IAN 71599 Manual

30
Zoom out
Zoom in
Previous page
1/34
Next page
30 GB
Securely support the workpiece.
A workpiece held in a clamp or vice is kept more
securely in place than one held by your hand.
POISONOUS DUSTS!
Harmful / noxious dusts generated from your
work represent a risk to the health of the person
operating the device and to anyone near the
work area.
Wear safety glasses and a dust
mask!
Do not drill any material containing
asbestos. Asbestos is a known carcinogen.
Hold the electrical power tool firmly.
High reaction torques may occur momentarily
during tightening or loosening of screws.
If the inserted tool jams, switch off the
electrical power tool immediately. Be
prepared for high reaction torques as they may
cause kickback. The inserted tool may jam if
the electrical power tool is overloaded or is
held at an angle to the workpiece.
Before you carry out any tasks on the
device, transport or store it, make sure
that the direction of rotation switch is
in the middle position (lock). To prevent
the device from starting up unintentionally.
Children or persons who lack the knowledge or
experience to use the device or whose physical,
sensory or intellectual capacities are limited
must never be allowed to use the device without
supervision or instruction by a person responsi-
ble for their safety. Children must never be
allowed to play with the device.
Q
Attention - Service lines!
Take steps to ensure that
you do not hit upon any service lines
(electricity, gas, water) when working
with electrical appliances. Check, if need be
with a service line detector, before you start to cut
or bore into a surface.
Q
Original ancillaries /
accessories
Use only the ancillaries and accessories
that are detailed in the operating
instructions. The use of ancillaries and ac-
cessories other than those recommended in the
operating instructions could lead to an in-
creased risk of personal injury for you.
Q
Before first use
Q
Removing / charging / inserting
rechargeable battery pack
Note: The battery is supplied partially charged.
Charge the rechargeable battery in the charging
station for at least one hour before first use. By doing
this the battery will operate at its highest capacity.
You can charge the Li-Ion battery at any time with-
out risk of shortening battery life. Interrupting the
charging process does not damage the battery.
1. In order to remove the rechargeable battery pack
8
, press the release buttons
9
and take the
rechargeable battery pack
8
out of the device.
2. Insert the rechargeable battery pack
8
into the
quick-charger
15
.
3. Insert the mains plug into the mains socket.
The indicator LED
13
illuminates red.
4. The green charge indicator LED
14
shows you
that the charging process is complete and the
battery pack
8
is ready for use.
5. Insert the rechargeable battery pack
8
into
the device.
Q
Checking the battery status
To check the battery status, press the button for
the rechargeable battery LED
2
(refer to main
diagram). The status or the remaining power
will be displayed in the rechargeable battery
LED
3
as follows:
RED / ORANGE / GREEN = maximum charge /
performance
RED / ORANGE = medium charge / performance
RED = low charge – recharge battery
Before first use / Preparing the tool for use General safety advice for electrical power tools / Before first use
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside PABS 10.8 B2 - IAN 71599 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside PABS 10.8 B2 - IAN 71599 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside PABS 10.8 B2 - IAN 71599

Parkside PABS 10.8 B2 - IAN 71599 User Manual - French, Italian - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info