745116
34
Zoom out
Zoom in
Previous page
1/36
Next page
34 GB
Warranty / Disposal / Declaration of Conformity / ManufacturerOperation / Maintenance and cleaning / Service / Warranty
Turn the exhaust air aperture
1
to guide the
exhaust airflow in the desired direction.
After finishing work, disconnect the device from
the compressor.
Removing jammed fasteners
If a staple or nail gets jammed in the magazine
slot, immediately disconnect the compressed
air supply.
Open the magazine
5
as described in the
chapter “Loading the magazine“.
Open the face plate
10
by pulling the face
plate quick clamping lever
11
in the direction
of the trigger lock
8
.
Remove the jammed fastener.
Close the face plate
10
by pulling the face
plate quick clamping lever
11
in the direction
of the exhaust air aperture
1
.
Close the magazine
5
of the compressed air
tacker as described in the chapter “Loading the
magazine“.
Maintenance and cleaning
RISK OF INJURY! Be absolutely certain to
disconnect the device from the compressed air
source before cleaning or maintaining it.
Maintenance
Lubrication with oil mister
NOTE: As a treatment stage after the pressure re-
ducer, an oil mister provides continuous and opti
mum
lubrication of the compressed air tacker. An oil mis-
ter gives off fine drops of oil into the airflow and so
guarantees regular lubrication.
Install the oil mister after the (filter) pressure re-
ducer. To do so, insert the nipple of the oil mis-
ter into the quick-release coupling of the (filter)
pressure reducer.
Then connect the compressed air device to the
quick-release coupling provided for it.
Manual lubrication
NOTE: If you do not have an oil mister, lubricate the
device each time after driving about 5000 fasteners.
Apply 1–2 drops of special compressed air oil
into the threaded nipple
4
of the compressed
air tacker.
Then press the trigger
2
several times.
ATTENTION: Be certain not to use too much
oil; otherwise oil could leave the mouth with the
fastener and potentially damage the workpiece.
Cleaning
Do not use any sharp objects to clean the device.
Do not allow any liquids to enter the device.
Otherwise the device could be damaged.
Clean the device regularly, preferably always
immediately after finishing work.
Use a dry cloth to clean the housing. Under no
circumstances should you use petrol, solvent or
cleaners which attack plastic.
After each use, pack the compressed air tacker
in the carrying case it was delivered with to
protect it from dirt.
Service
Have your fastener
driving tool repaired only by qualified
specialist personnel using original man-
ufacturer parts only. This will ensure that
your fastener driving tool remains safe to use.
Warranty
The warranty for this appliance is for 3
years from the date of purchase. The ap-
pliance has been manufactured with care
and meticulously examined before deliv-
ery. Please retain your receipt as proof
of purchase. In the event of a warranty
claim, please make contact by telephone
with our Service Department. Only in this
way can a post-free despatch for your
goods be assured.
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 89568 PDT 40 C2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 89568 PDT 40 C2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info