744943

Parkside IAN 75636 PABS 18 Li B2 Manual

48
Zoom out
Zoom in
Previous page
1/52
Next page
48 GB
Preparing the tool for use / Cleaning and Maintenance / Service / WarrantyBefore first use / Preparing the tool for use
Select a high setting for large screws, hard
work materials and for the extraction of screws.
For drilling, push the selector to the setting for
drilling, in that you adjust the torque pre-selector
to the position
.
For drilling tasks, also push the gear selector
switch
1
to the front (Position: 2).
Q
2 Gear Drive
CAUTION! Move the gear selector switch
1
only after the device has come to a standstill.
Failure to observe this advice may result in damage
to the device.
In the first gear (Gear selector switch
1
in Position: 1)
A speed of up to approx. 400 rpm can be achieved
and a high torque. This setting is intended for use w
ith
all screwing tasks and for accessories (see example
Fig. B).
In the second gear (Gear selector switch
1
in Position: 2)
It achieves a speed of up to approx. 1400 rpm, for
the carrying out of drilling tasks (see example Fig. A).
Q
Preparing the tool for use
Q
Switching ON /OFF
Switching on:
To start the appliance squeeze on the ON /
OFF switch
3
and then keep it pressed down.
The LED working light
12
comes on with a slightly
or fully pressed ON /OFF switch
3
and illumi-
nates the working area in poor lighting conditio
ns.
Switching off:
To stop the appliance, release the ON / OFF
switch
3
.
Switching the LED light on and off
Switching on:
Press the LED light button
8
to switch on the
LED light
9
.
Switching off:
Press the LED light button
8
again to switch
off the LED light
9
.
Q
Adjusting the speed
The ON / OFF switch
3
has a variable speed con-
trol device. Slight pressure on the ON / OFF switch
3
will cause the rotation speed to slow down. With
increased pressure, the rotational speed will increase.
Note: The integrated engine brake means that the
device will come to a fast standstill.
Q
Switching direction of rotation
To switch the direction of rotation, push the
direction of rotation switch
2
to either the
right or to the left.
Q
Tips and Tricks
Before you use the appliance, check to see
that the screw or drill bit is properly fitted, i.e.
located centrally in the chuck.
Screw bits are designated with their dimensions
and their shape. If you are unsure, always try
the particular screw bit out to see whether it sits
in the screw head without any free play.
Torque:
Smaller screws and bits in particular can be
easily damaged if you adjust the appliance
with too high a torque and/or rotation speed.
Hard screwdriving conditions (into metal):
Particularly high torques can occur, for example
with metal screws tightened by socket tool bits.
Select a lower rotation speed.
… 48 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 75636 PABS 18 Li B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 75636 PABS 18 Li B2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info