Manual Parkside IAN 73790 PDMH 4500 A2 (page 44 of 50) (English, German, Dutch, French)

745068

Zoom out

Zoom in

1/50

- 44 -

Residual risks

Even if you use the equipment in ac-

cordance with the instructions, certain

residual risks cannot be eliminated. The

following hazards may arise in connec-

tion with the equipment’s construction

and layout:

1. Lung damage if no suitable protective dust

mask is used.

2. Damage to hearing if no suitable ear protec-

tion is used.

3. Health damage caused by hand-arm vib-

rations if the equipment is used over a pro-

longed period or is not properly guided and

maintained.

Air supply:

Via a compressed air source with pressure setting

function, e.g. a compressor. Before starting up,

please also read section 7 “Care and mainte-

nance”.

Performance values of the compressor:

The compressor used should have a tank volume

of at least 50 liters and a motor rating of approx.

2.2 kW.

Setting values for work with the suction

spray gun:

Set a maximum working pressure of 6.3 bar at

your compressed air supply.

6. Before starting the

equipment

Fig. 3

Screw the supplied nipple (4) into the air connec-

tion after you have wound 2-3 layers of sealing

tape around the thread. Plug the required chisel

into the hexagon mount of the chisel hammer. Slip

the tensioning spring (5) over the chisel. Turn the

tensioning spring onto the thread of the cylinder

(1) as far as the stop. As you do this, hold the ten-

sioning spring by the front arm.

Connect the chisel hammer to a compressor or

compressed air network with matching power. Do

this with a ﬂ exible compressed air hose

(Ø 10 mm internal) with quick-lock coupling.

Make sure that the air regulation screw (3) is

adjusted so that air can ﬂ ow through. Move the

chisel hammer towards the object you want to

work on. Actuate the trigger lever (2) to start the

chisel hammer.

Check the equipment and the mounted tool each

time before use. This also includes checking the

speed and the level of vibrations.

To change the chisel you must ﬁ rst disconnect the

equipment from the compressed air source. Turn

the tensioning spring off the cylinder of the chisel

hammer by holding it by its rear arm. The chisel

can now be changed as described above.

The chisel shaft should be lubricated with a little

normal lubricating grease from time to time.

7. Maintenance and care

Important: Disconnect the equipment from the

compressed air supply before you carry out any

maintenance or cleaning work.

Compliance with the maintenance instructions lis-

ted here will help this quality product provide you

with a long service life and trouble-free operation.

Clean the equipment thoroughly and immediately

each time after it has been used.

Regular lubrication is essential for your chisel

hammer to work properly for a prolonged peri-

od of time. Use only special compressed air oil

as supplied. Special compressed air oil is also

available from your dealer.

Note: Use environmentally friendly compressed

air oil if you want to operate the equipment out-

side the workshop.

Anleitung_4139031_LB2.indb 44Anleitung_4139031_LB2.indb 44 03.04.12 10:1403.04.12 10:14

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 73790 PDMH 4500 A2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 73790 PDMH 4500 A2 Manual

Product: