745200
29
Zoom out
Zoom in
Previous page
1/33
Next page
29 GB
General safety advice on power tools
5. Service
a) Only have the power tool repaired by
qualified professionals using OEM
spare parts. This ensures the safety of the
power tool is maintained.
Safety notes for hammer drills
Wear hearing protection. Exposure to
noise can cause hearing loss.
Use the additional handle when using
the device. Losing control can lead to injury.
Hold the device by the insulated han-
dles when performing work n appli-
cations where a potential danger of
the tool striking hidden electrical lines
or its own power cable. Contact with a
live wire could cause metal parts of the device
to become live and lead to electric shock.
Wear a dust mask.
TOXIC DUST! Working on
materials which can produce harmful / toxic dusts
presents a health risk to the user and people
within close vicinity.
CAUTION - LEADS! DANGER! Verify you
will not strike electric-, gas- or water lines whilst
using the power tool. If necessary, first use a
cable detector before drilling into or cutting
open a wall.
Start-up
Pivot additional handle
Note: For safety reasons this device must only be
used with the additional handle
7
installed (also
see Fig. C, D, E).
The position of the additional handle
7
can be
adjusted. Turn the wing screw
1
anti-clockwise
and swivel the additional handle
7
into the
desired position.
Then tighten the wing screw
1
again.
This unit features an LED
5
. It will light up once
the unit is connected to the mains, indicating
the unit is energised and will immediately switch
on when the ON / OFF switch
3
is activated.
Depth stop
Open the wing screw
1
.
Insert the depth stop
11
in the additional
handle
7
.
Make sure that the toothing on the depth stop
11
is pointing downwards.
Pull the depth stop
11
out as far as necessary
so that the distance between the tip of the drill
and the tip of the depth stop corresponds to
the desired drilling depth.
Firmly tighten the wing screw
1
.
Inserting / removing tools
Inserting tools:
Lightly grease the tool holder before inserting
the tool
8
.
To insert, pull back the locking sleeve
10
and
insert the tool.
Release the locking sleeve
10
. This locks the
tool holder. Pull the tool to ensure that it is firm-
ly locked in place. The tool has some radial play
inherent in the system.
Removing tools:
To remove the tool pull back on the locking
sleeve
10
.
Quick-release chuck for
round shaft drills
Do not use the quick-release
chuck for round shaft drills for hammer drilling or
chiseling applications!
Set the function selector switch
6
to the drill
symbol
.
General safety advice on power tools / Start-up
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 46883 PBH 1050 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 46883 PBH 1050 A1 in the language / languages: French as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 46883 PBH 1050 A1

Parkside IAN 46883 PBH 1050 A1 User Manual - English, German, Dutch - 31 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info