Manual Parkside IAN 275681 PDBS 6.2 A1 (page 37 of 41) (French)

745541

Zoom out

Zoom in

1/41

38 GB

Cleaning and storage / Information about warranty and service processingStart-up / After initial use / Cleaning and storage

Cutting

Activate the trigger

to start using the shears.

Move the metal shears toward the item you wish

to work on. If possible, already run the shears

at full speed when applying them.

Note: The shears may take up to 8 seconds to

be fully ready for use and reach full force. Dur-

ng this time you should wait before applying th

shears to ensure better cutting results and treat

the device with care.

Note: Do not apply too much pressure whilst

cutting. Do not overburden the shears. In additio

to possible unclean cutting results, this could also

cause metal slivers to chip oﬀ and ﬂy about.

Note: Metal slivers ﬂying about can be very

dangerous!

Note: If the compressed air supply is tempo-

rarily cut oﬀ due to power failure or temporary

compressor failure, immediately release the trig-

ger

. If you now wish to continue working,

you must ﬁrst remove the metal shears all the

way out of the work piece. You can then con-

tinue working.

When using the device always be aware of the

following items:

The shears must always operate at full speed.

This means, the compressor must always supply

suﬃcient pressure and air volume.

- Work slow. Slowly guide the shears along the

work piece and work without applying exces-

sive pressure.

- Move the shears smoothly.

- Do not tilt the shears.

Please tighten the screws of the cutter head re-

gularly and replace worn or damaged cutting

edges if necessary (see Fig. E).

Use the corresponding Allen key when doing this.

Check the cutter head after 2 minutes of conti-

nuous operation to ensure it is securely seated.

After initial use

Once the task has been ﬁnished the equipment must

be disconnect from the compressed air supply.

This ﬁrst requires the pressure to be completely re-

leased from the lines.

Switch oﬀ the compressor.

To release potentially remainders of compressed

air, brieﬂy activate the trigger

of the device.

Pull back the lock.

Take oﬀ the coupler.

Spare parts / replacing

consumables

When replacing items, always be sure the com-

pressed air supply is disconnected!

ote: The shear head does not necessarily ha

to be removed all the way. After loosening the

screws you can remove the parts of the cutter

blades to replace the defective part.

Use a ﬁtting hex wrench to loosen the screws on

the underside of the shear head (see Fig. E). Re-

move the blades and replace the defective part.

During assembly be sure the blades are corre

ctly

aligned.

First insert the lower blade.

Then insert the centre piece.

Then insert the marked ring. This is merely a spacer

between the upper and lower blade.

Now insert the upper blade and secure the shear

head with the screws.

Note: please note, the notches on the blades

must face the inside.

Cleaning and storage

To ensure a long life and trouble-free operation, it‘s

important to observe the following instructions.

Always disconnect the tool from the compressed

air source before cleaning it.

Clean your tool with a soft, dry cloth or lightly

blow it out with compressed air. Never use

caustic cleaners.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 275681 PDBS 6.2 A1 in the language / languages: French as an attachment in your email.

The manual is 1,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 275681 PDBS 6.2 A1

Parkside IAN 275681 PDBS 6.2 A1 User Manual - English, German, Dutch - 39 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 275681 PDBS 6.2 A1 Manual

Product: