745532

Parkside IAN 273482 PTSS 1200 A1 Manual

48
Zoom out
Zoom in
Previous page
1/52
Next page
45
PTSS 1200 A1
GB
Eccentric screws
The eccentric screws are intended for adjusting
the fit of the base plate
on the guide rail .
♦ Tighten the eccentric screws
to reduce the
play between the circular saw and the guide
rails
.
Sawing (without guide rail)
Right-angled sawing
♦ Hold the machine with both hands firmly on the
handles
and .
♦ Switch on the appliance as described in
"Switching on and off".
♦ Place the appliance with the front part of the
base plate
on the workpiece.
♦ Swivel the motor down and saw forwards with
moderate pressure – never backwards.
Mitre angles up to 45°
♦ Adjust the cutting angle and cutting line as
described.
♦ Hold the machine with both hands firmly on the
handles
and .
♦ Switch on the appliance as described in "Switch-
ing on and off". Place the appliance with the front
part of the base plate
on the workpiece.
♦ Swivel the motor down and saw forwards with
moderate pressure – never backwards.
Plunge cuts
♦ When making a "plunge cut" which is not at
right angles, secure the base plate of the saw to
prevent any lateral movement. Lateral movement
can cause the saw blade to jam, thus causing
a kickback.
♦ Adjust the desired cutting depth as described
above.
♦ Place the appliance on the workpiece.
♦ Avoid kickback and place the rear edge against
a stop (as referenced in the section "Plunge
cutting with guide rail").
♦ Switch on the appliance as described in
"Switching on and off".
♦ Hold the machine with both hands firmly on the
handles
and and pivot it.
NOTE
► The cut width marking
on the side of the
blade guard shows the front and rear cutting
point of a 165 mm at maximum cutting
depth. This applies both to plunge cuts with
guide rail
and plunge cuts without guide
rail .
Sawing (with guide rail)
Right-angled sawing with guide rail
♦ Place the guide rail
with the foam rubber
element on the workpiece.
♦ Place the appliance with the groove
onto the
guide rail .
♦ Switch on the appliance as described in
"Switching on and off".
♦ Hold the machine with both hands firmly on the
handles
and and pivot it.
Mitre angles up to 45°
♦ Apply the guide rail
with the foam rubber
element onto the workpiece.
♦ Place the appliance with the groove
onto the
guide rail .
♦ Adjust the cutting angle and cutting line as
described.
♦ Hold the machine with both hands firmly on the
handles
and .
♦ Switch on the appliance as described in
"Switching on and off". Place the appliance
with the front part of the base plate
on the
workpiece.
♦ Swivel the motor down and saw forwards with
moderate pressure – never backwards.
… 48 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 273482 PTSS 1200 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273482 PTSS 1200 A1 in the language / languages: French, Italian as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 273482 PTSS 1200 A1

Parkside IAN 273482 PTSS 1200 A1 User Manual - English, German, Dutch - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info