612721
31
Zoom out
Zoom in
Previous page
1/32
Next page
RQT7799
15
Troubleshooting guide
Before requesting service, make the checks below. If you can’t fix the system as described below, or if something not listed here occurs, refer to the
enclosed directory to locate an Authorized Service Center convenient to you or contact your dealer.
Reference pages are shown as black circled numbers 4.
Common Problems
Although the unit is in standby
mode, the display lights up and
changes continuously.
No sound.
Sound stops.
Sound is unfixed, reversed or
comes from one speaker only.
Humming heard during play.
“ERROR” is displayed.
“– –:– –” appears on the display
at standby mode.
“F61” is displayed.
Turn off the demo function. 4
If you set the clock, demo function will be turned off automatically. @
Turn the volume up.
Switch off the unit, determine and correct the cause, then switch the unit on. Causes include shorting
of the positive and negative speaker wires, straining of the speakers through excessive volume or
power, and using the unit in a hot environment.
Check the speaker connections. 4
An AC power supply cord or fluorescent light is near the cables. Keep other appliances and cords
away from this unit’s cables.
Incorrect operation performed. Read the instructions and try again.
You plugged the AC power supply cord in for the first time or there was a power failure recently. Set
the time. @
Check and correct the speaker cords connection. 4
If this does not fix the problem, there is a power supply problem. Consult the dealer.
The display is wrong or play
won’t start.
Cannot perform all-disc
random play.
The total number of tracks
displayed differs each time the
same disc is inserted. Unusual
sound is heard.
CD-RW cannot be read.
“VBR–” is displayed instead of
the remaining play time.
“TAKE OUT/DISC” appears on the
display.
The disc may be upside down. 6
Wipe the disc.
Replace the disc if it is scratched, warped, or non-standard.
Condensation may have formed inside the unit due to a sudden change in temperature. Wait for
about an hour for it to clear and try again.
All-disc random mode cannot be used for MP3 discs. Change the disc or select another play
mode. 7
The disc may be scratched, or its data may be defective. Replace the disc.
The disc was incompletely formatted. Use the recording equipment to fully format the disc before
recording.
The unit cannot display the remaining play time for variable bit rate (VBR) tracks.
There is a problem with the disc mechanism. (A power failure may have occurred.)
The tray will open automatically. Remove the disc from the tray, and after ensuring there is no disc in
the tray, close it. The unit will make the disc changing noises for a few moments and then it should
operate normally.
Playing discs
Noise is heard.
The stereo indicator flickers or
doesn’t light.
Sound is distorted.
A beat sound is heard.
A low hum is heard during AM
broadcasts.
Use an outdoor antenna. !
Turn the TV off or separate it from the unit.
Separate the antenna from other cables and cords.
Listening to the radio
When there is a television set nearby
The picture on the TV disappears
or stripes appear on the screen.
The location and orientation of the antenna are incorrect. If you are using an indoor antenna, change
to an outdoor antenna.
The TV antenna wire is too close to the unit. Separate the antenna wire of the TV set from the unit.
Poor quality sound.
Recording is not possible.
Using the cassette deck
Clean the heads. ^
If the erasure prevention tabs have been removed, cover the holes with adhesive tape. @
Remote control doesn’t work.
Check that the batteries are inserted correctly. 3
Replace the batteries if they are worn.
Remote control
Memory reset (Initialization)
When the following situations occur, refer to the instructions below to reset the memory:
There is no response when buttons are pressed.
You want to clear and reset the memory contents.
To reset memory
1 Disconnect the AC power supply cord. (Wait at least 3 minutes before proceeding to step 2)
2 While pressing and holding down [
ff
ff
f/7, POWER] (
PL
) or [
ff
ff
f/7] (
GCP
) on the main unit, reconnect the AC power supply cord.
“– – – – – – – – –” appears on the display.
3 Release [
ff
ff
f/7, POWER] (
PL
) or [
ff
ff
f/7] (
GCP
).
All the settings are returned to the factory preset.
You will need to reset the memory items.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic SCAK331 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic SCAK331 in the language / languages: English, Spanish as an attachment in your email.

The manual is 2,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic SCAK331

Panasonic SCAK331 User Manual - Spanish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info