7
How to remove the built-in
rechargeable battery before dis-
posal of the shaver
(see fig. 10)
The battery in this shaver is not
intended to be replaced by consum-
ers. However, the battery may be
replaced at an authorized service
center. The procedure described
below is intended only for removal of
the rechargeable battery for the pur-
pose of proper disposal.
Always make sure that the battery
have been removed from the shaver
before disposing of it.
1. Disconnect the power cord from
the AC outlet, and remove the
power cord from the shaver.
2. Remove the outer foil frame and
the inner blades.
3. Remove the trimmer driving bar
(a), and two screws (b).
4. Remove the screw (c) and the
bottom cover (d).
5. Remove the two screw covers (e)
(using something like a toothpick),
two screws (f), and the panel cov-
ers (g).
6. Remove the four screws (h), and
the back panel (i).
7. Remove the battery from the bat-
tery block (j).
Caution
• Do not charge the shaver where the
temperature is below 0°C (32°F) or
above 40°C (104°F), where it will
be exposed to direct sunlight or a
heat source, or where there is a lot
of moisture.
• Use only the included power cord
RE7-20 to charge the ES4032/
ES4033 shaver.
• Dry the shaver completely before
charging it.
• Keep the power cord away from
water and handle only with dry
hands.
• Grip the plug when disconnecting it
from an AC outlet; tugging on the
power cord may damage it.
• Store the power cord in a dry area
where it will be protected from dam-
age.
• Do not pull, twist, or severely bend
the power cord.
• Do not wrap the power cord tightly
around the appliance.
• The outer foil is very thin. If handled
improperly, it can be easily dam-
aged. To avoid personal injury, do
not use the shaver if it has a dam-
aged foil or inner blade.
• Place protective cap over shaver
head after use.
• Wash the shaver in tap water. Do
not use salt water or boiling water.
Also, do not use cleaning products
that are designed for toilets, bath-
rooms or kitchen appliances. Do
not submerge the shaver for a long
time.
• Do not wipe any part of the shaver
with thinner, benzine or alcohol.
Clean it by using a cloth dampened
with soapy water.
• Do not take the housing apart as
this can affect the watertight con-
struction.
• Do not clean with water when the
shaver is connected to the power
cord.
6
Cleaning your shaver
(see fig. 5)
For cleanliness and convenience, we
recommend that you clean your
shaver with water and a liquid hand
soap. Regular cleaning will keep your
shaver in good condition while pre-
venting odors or bacteria from devel-
oping, and maintain the cutting
performance.
With the outer foil in place, apply
some hand soap onto the outer foil.
Turn the shaver on and pour some
water over the outer foil.
After about 10-20 seconds, turn the
shaver off.
Remove the foil frame and clean it
with running water.
Wipe off any moisture from the
shaver with a dry cloth and remove
the protective cap to allow the outer
foil to dry completely.
Brush cleaning
Squeeze the outer foil release but-
tons and lift the outer foil upward to
remove it. Remove the inner blades
one at a time by grasping it firmly at
both ends and pulling it straight away
from the shaver (see fig. 7). Clean
the outer foils, the shaver body and
the trimmer with the long brush (see
fig. 8). Clean the inner blades with
the short brush by moving it in the
direction in fig. 9(A). Do not use the
short brush to clean the outer foils.
Replacing shaving head
components
It is recommended that you replace
the outer foil at least once a year and
the inner blades at least once every 2
years to maintain your shaver’s cut-
ting performance.
Replacing the outer foil
(see fig. 6)
Squeeze the outer foil release but-
tons and lift the outer foil upward to
remove it. To insert the new outer foil,
press down until it snaps into place.
Replacing the inner blades
(see fig. 7)
Squeeze the foil frame release but-
tons and lift the foil frame upward to
remove it. Remove the inner blade,
one at a time, by grasping them firmly
at both ends and pulling straight
away from the shaver. To insert the
new inner blade, hold the blade, one
at a time, at both ends and press
downward until it snaps into the
shaver.
For environmental protec-
tion and recycling of mate-
rials
This shaver contains Nickel-Metal
Hydride battery.
Please make sure that the battery is
disposed of at an officially assigned
location, if there is one in your coun-
try.
Warning – To prevent electric
shock or personal injury, discon-
nect the power cord from the
shaver and turn the shaver off
before cleaning.
