633078
15
Zoom out
Zoom in
Previous page
1/17
Next page
Preparation
Disconnect the cable from the negative battery
terminal (see warning and caution below).
Remove Mounting Collar q and Trim Plate u from the
main unit temporarily, which are already mounted at
shipment.*
Unit should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30°.
Dashboard Installation
Installation Opening
This unit can be installed in any dashboard having
an opening as shown below. The dashboard should
be 3 16" (4.75 mm)–7 32" (5.56 mm) thick in
order to be able to support the unit.
17
E
N
G
L
I
S
H
18
E
N
G
L
I
S
H
2928
CQ-C1200U/C1120U/C1110U/C1100U CQ-C1200U/C1120U/C1110U/C1100U
Cautions:
¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries.
¡
When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your
hands and fingers.
1
2
3
4
Mounting Holes
t Mounting Bolt
Insert Trim Plate u.
After installation reconnect the negative
(–) battery terminal.
First complete the electrical connections, and
then check them for correctness.(
a page 30)
The included Mounting Collar q is
designed specially for this unit. Do
not use it to attach any other model.
Mounting Springs (
C)
y Power Connector
Engage the Mounting
Springs (
C) in the
mounting holes of the
Mounting Collar q
firmly.
Mounting Spring
Mounting
Hole
Insert Mounting Collar q into the dash-
board, and bend the mounting tabs out
with a screwdriver.
The tabs to be bent vary depending on
the car. To securely install the unit, fully
bend a number of the tabs so that there
is no rattling.
Example:
Tab
q Mounting
Collar
(a) Using the rear support strap e
r Tapping screw
(5 mmø×16 mm)
w Hex. nut
(5 mmø)
e Rear support strap
t Mounting bolt (5 mmø)
q Mounting collar
Fire wall of car
3 mmø
(b) Using the rubber cushion (option)
t Mounting bolt
(5 mmø)
q Mounting collar
Rear support bracket
(provided on the car)
Rubber cushion (option)
Establish the rear connection of the unit.
After fixing Mounting Bolt t and Power Connector
y, fix the rear of the unit to the car body by either
method (a) or (b) shown the previous page.
Installation (Continued)
Installation Hardware
i
Dismounting Plate
(YFX214C323ZA)
1
2
Less than 30°
Caution: Various settings that have been stored in the
memory in other on-board equipment (car navigation
etc.) may be lost if the battery terminals are discon-
nected.
Therefore, we recommend to make a record of or to
back up the settings before disconnecting the termi-
nals.
After completing installation of the main unit, set the
equipment again according to the record.
Warning: If your car is equipped with air bag
and/or anti-theft systems, specific procedures
may be required for connection and disconnec-
tion of the battery to install this product.
Before attempting installation of this electronic
component, contact your car dealer or manufac-
turer to determine the required procedure and
strictly follow their instructions.
FAILURE TO FOLLOW THE PROCEDURE MAY
RESULT IN THE UNINTENDED DEPLOYMENT OF
AIR BAGS OR ACTIVATION OF THE ANTI-THEFT
SYSTEM RESULTING IN DAMAGE TO THE VEHI-
CLE AND PERSONAL INJURY.
ItemNo. Diagram Q’ty
t
y
u
Mounting Collar*
(FX0214C316ZA)
Hex. nut (5 mmø)
(YJN994C002ZA)
Rear support strap
(YFG044C002ZA)
Tapping screw (5 mmø×16 mm)
(XTT5+16AFK)
Mounting Bolt (5 mmø)
(YEJV014C002A)
Power Connector
(YEAJ02877)
Trim Plate*
(YFC054C063ZA)
1
1
1
1
1
1
q
w
e
r
(182 mm)
(53 mm)
7
5
/
32
"
2
3
/
32
"
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic CQ-C1110U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic CQ-C1110U in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info