683951
1
Zoom out
Zoom in
Previous page
1/2
Next page
A
C
B
D
de
DIMMER UNIVERSAL RLC LED
4-KANAL
TECHNISCHE DATEN
BESCHREIBUNG / BESTIMMUNGSGEMÄSSE VERWENDUNG
Universeller Dimmaktor (Verteilereinbau) mit 4 Kanälen, zur Phasenan-/
abschnittsteuerung von modernen Leuchtmitteln (RLC, LED):
- Glühlampen & Halogenleuchten 230V~.
- Halogenleuchten mit elektronischem Transformator.
- Dimmbare LED Leuchten 230V~.
- Dimmbare LED Leuchten 12V~ mit elektronischem Transformator.
Die vier Ausgänge sind separat regelbar.
Eingebauter Drehregler (D) zum manuellen Testen der Dimmfunktion, auch
ohne vorherigen Anschluss an den KNX-Bus:
· Man.: Ansteuerung / Regelung der angeschlossenen Leuchten mittels
Drehregler (KNX-Busanschluss nicht norwendig).
· Auto: Ansteuerung / Regelung der angeschlossenen Leuchten über den
KNX-Bus.
Integrierter Schutz gegen Überlast und Kurzschluss. Integrierter
Überhitzungsschutz (rücksetzbar).
Anti-Panik Eingang (A): Durch unterbrechen (öffnen) des Eingangs werden
alle angeschlossenen Leuchten mit maximaler Helligkeit eingeschaltet,
jegliche Dimmfunktionen werden ignoriert.
Programmierung und Konfiguration mittels ETS4 oder höher.
Integrierte KNX-Busklemme (C).
Anschlusspannung 230V~ 50Hz
Anschlusspannung KNX-Bus 21 - 32V DC (über Bus)
Busstrom < 10mA
Applikationssoftware ETS4 oder höher
KNX Medium KNX-TP
Anzahl Ausgänge / Kanäle 4
Konfigurationsmodus System-Mode (S-Mode)
Montage 35 mm DIN-Schiene
Lagertemperatur -30ºC ... +70ºC
Schutzart IP20 (EN60529)
Angewandte Richtlinien Niederspannungsrichtlinie 2014/35/EU
EMV Richtlinie 2014/30/EU
Isolationsspannung 4KV AC (Versorgungsspannung / Bus)
Last
Glühlampen
Halogenleuchten 230V
Halogenleuchten mit elektronischem Trafo
LED Leuchten 230V~
(Phasenanschnitsteuerung)
LED Leuchten 230V~ (Phasenabschnitsteuerung)
LED Leuchten 12V~ (mit elektronischem Trafo)
4 ~ 300W pro Kanal
4 ~ 300W pro Kanal
20 ~ 280VA pro Kanal
4 ~ 120W pro Kanal
4 ~ 250W pro Kanal
10 ~ 280W (des Trafos) pro Kanal
Abmessungen 5 TE, 87,5mm x 65mm
Betriebstemperatur -5ºC ... +45ºC
Angewandte Normen EN 50491-3:2009
EN 50491-5-2:2010
EN 50491-4-1:2012
EN 60669-1:1999/A2:2008
EN 60669-2-1:2004/A12:2010
en
UNIVERSAL DIMMING ACTUATOR RLC LED
4-CHANNEL
TECHNICAL DATA
Power supply 230V~ 50Hz
Supply voltage KNX bus 21 - 32V DC (via Bus)
Bus current < 10mA
Application software ETS4 or later
KNX media KNX-TP
Number of outputs / channels 4
Commissioning mode System-mode (S-mode)
Isolation voltage 4 KV AC (bus / mains voltage)
Load
Incandescence
Halogens 230V
Halogens with electronic transformer
230V~ LED Lamps
(dimmable by leading-edge)
230V~ LED Lamps (dimmable by trailing-edge)
12V~ LED Lamps (with electronic transformer)
4 ~ 300W per channel
4 ~ 300W per channel
20 ~ 280W per channel
4 ~ 120W per channel
7 ~ 250W per channel
10 ~ 280W (of transformer) per channel
Mounting 35 mm DIN-rail
Storage temperature -30ºC ... +70ºC
Degree of protection IP20 (EN60529)
According to the directives Low-voltage 2014/35/EU
EMC 2014/30/EU
Dimensions 5 modules wide, 87.5mm x 65mm
Operation temperature range -5ºC ... +45ºC
According to the standards EN 50491-3:2009
EN 50491-5-2:2010
EN 50491-4-1:2012
EN 60669-1:1999/A2:2008
EN 60669-2-1:2004/A12:2010
DESCRIPTION / INTENDED USE
4-channel universal modular dimming actuator (DIN-rail mounting) for
leading and trailing edge phase control (R, L & C loads):
- Incandescence & Halogens 230V~.
- Halogens with electronic transformer.
- Dimmable 230V~ LED lamps.
- Dimmable 12V~ LED lamps with electronic transformer.
The four output channels can be controlled independently.
Built-in potentiometer (D), which allows to test manually the correct
operation of the dimmer, without connecting the KNX-Bus:
· Man.: Manual control (dimming) of connected lamps via the
potentiometer (no KNX-Bus connection necessary).
· Auto: Controlling / dimming of connected lamps via KNX-bus.
Protected against overloads and short-circuits. Built-in (resettable) heating
protection.
Anti-panic input (A): Disabling (opening) this input will turn on all connected
lamps at maximum brightness, ignoring dimming parameters.
Programmation and commissioning by ETS4 or later.
Built-in standard KNX terminal connector (C).
879 414 knx
Service:
Hugo Müller GmbH & Co KG
Sturmbühlstraße 145-149
DE-78054 VS-Schwenningen
Deutschland / Germany
+49 7720 80836
www.hugo-mueller.com
BA 879414knx Hardware P;de,en 2018.07V01.pdf
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 879 414 knx at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 879 414 knx in the language / languages: English, German as an attachment in your email.

The manual is 2,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info