683927
2
Zoom out
Zoom in
Previous page
1/2
Next page
BA 873040led N;DE,GB -23435- 2016.11V02
INSTRUCTION MANUAL DIMMER [LED STRIPES]
Technical Features Safetey instructions
Supply voltage 12 – 48 VDC*
CAUTION!! DANGER OF LIFE / RISK OF FIRE AND ELECTRIC SHOCK!!
Power consumption 0,5 VA
Suitable type of lamps Dimmable LED lamps
Maximum load 8A
Installation and assembly of electrical equipment must be carried out only by professional electrician!
Connect the supply voltage/frequency as stated on the product!
Disconnect device from power supply for wiring and installation purposes!
Check power supply is disconnected!
Defective devices have to be put out of service immediately
No safe electrical isolation between the power supply and pushbutton 2!
When using a 230V~ pushbutton on P
L
und P
N
no low voltage protection, no SELV!
Warranty void if housing opened by unauthorized person!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if
external influences exceed certain limits!
Installation and assembly of electrical equipment must be in accordance with local building and electrical codes
Max. number of pushbuttons Unlimited (non-lighted pushbuttons)
Pushbutton 1 Pushbutton referred to Ground
Optional: Pushbutton 2 Pushbutton referred to 230V~ (no SELV)
Dimensions 46 x 42 x 13 mm
Weight 23 g
Permitted ambient temperature
Storage temperature
0º … +40ºC
-30º … +70ºC
Type of protection IP20 according to DIN EN 60529
*NOTE: The power supply associated with this dimmer should comply with the Low Voltage Directive 2006/95/EC and EMC
Directive 2004/108/EC
Important Note
For all lamps, please take into account the specifications of the manufacturer!
Description / Installation / Operation Wiring diagram
Description / Intended use
Dimmer for LED lamps 12 - 48VDC up to 6A, with Pulse Width Modulation technology (PWM),
specially designed for 1-channel LED strips.
Small size dimmer, for flush-mounting (e.g. behind standard pushbutton).
Protected against overload and short circuit. Built-in heat protection.
Can be used with a pushbutton referred to Ground (Pushbutton 1) or a pushbutton referred to 230V~ (Pushbutton 2) or both.
When using a 230V~ pushbutton on P
L
und P
N
the low voltages are not SELV!
With or without memory function.
With two function rotary switches:
min: minimum brightness level (1% up to ~60%).
dim speed: dimming speed between 3 and 10 sec. (from 0 to 100%).
Installation
1 Disconnect installation from power supply and check that power supply is disconnected.
2 Install the dimmer according to the wiring diagram.
3 Make sure the loads are connected properly and reconnect power supply.
4 Press shortly the pushbutton to switch the lamps on and dim with a long press to the minimum brightness level.
5 If you like the change the minimum brightness level you have to disconnect the installation again from power supply and set
with the rotary switch (min) the desired minimum brightness level.
.
Operation
Press shortly the pushbutton to switch the lamps on and off!
=> Switch on „No Mem“ = Lamp(s) switches on with max. brightness.
=> Switch on „Mem“ = Lamp(s) switches on with the brightness of the last switch off
With a long press you can dim!
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 873 040 led at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 873 040 led in the language / languages: English, German as an attachment in your email.

The manual is 0,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info