683964
1
Zoom out
Zoom in
Previous page
1/2
Next page
Measurement accuracy
Threshold accuracy +/- 0,5ºC
Protection degree IP20
Working temperature -10ºC ~ +70ºC
Dimensions 78 x 28 x 23mm
Radio-Frequency
Codified transmission in 868,3MHz
Range: 100m (in the free field)
Compatible with
RF-KNX:
CH_Room_Temperature_Sensor (0025h)
CC_HVAC_Mode
CC_TRSUA (TemperatureRoomStepUserAbs)
CH_Battery_Status (0021h)
+/- 0,3ºC
GB
WIRELESS TEMPERATURE SENSOR WITH MANUAL
TEMPERATURE ADJUSTMENT KNOB
TECHNICAL DATA
DESCRIPTION
RF-KNX compatible thermostat, for general purpose, including:
- Temperature sensor.
- Wheel for selecting the desired temperature, with OFF position.
The commissioning of the sensor is carried out via a pushbutton located inside the
device (A). It also allows to send the current temperature value.
Avoid using the transmitter close to radioelectric devices, microwaves,...
Leave at least a minimum distance of 2m between the transmitter and the receiver.
WORKING MODES
This device sends the temperature value when:
1.- The temperature measurement changes more than 0,5ºC in relation to the previous
transmission.
2.- Cyclically after the last transmission.
3.- Pressing shortly the linking key (A).
The desired temperature selection is done by matching the temperature value with the
selection point. This value will be sent via RF.
When the selection wheel indicates the current temperature, measured by the sensor
temperature, the red LED will turn on for 1 second.
When the selection wheel is positioned at OFF point, the thermostat will send a STANDBY
telegram.
Once the selection wheel is positioned outside the STANDBY position, the thermostat sends
AUTO telegram.
Both, selected temperature value as the status of the thermostat (STANDBY or AUTO), will
be sent spontaneously in cycles of ~60 minutes.
LINK PROCEDURE
To link the temperature sensor with a compatible RF-KNX actuator:
1.- Set the RF actuator in link mode according to the instructions given by the
manufacturer.
2.- Press the link key once for more than 1 second.
3.- Check the correct link between the two devices in the actuator, according to the
instructions given by the manufacturer.
Battery life (estimated) >8 years
Power supply 1 battery 3V CR2450 (included)
DE
676 311 rf
PULL THE PLASTIC FOIL OUT TO ACTIVATE THE BATTERY
Messgenauigkeit
Schwellwert-Genauigkeit +/- 0,5ºC
Schutzart IP20
Betriebstemperatur -10ºC ~ +70ºC
Abmessungen 78 x 28 x 23mm
Funkfrequenz
Verschlüsselte Übertragung, 868,3MHz, ERP > 8 mW,
Reichweite: 100m (auf freiem Feld)
Kompatibel mit
RF-KNX:
CH_Room_Temperature_Sensor (0025h)
CC_HVAC_Mode
CC_TRSUA (TemperatureRoomStepUserAbs)
CH_Battery_Status (0021h)
+/- 0,3ºC
FUNK-TEMPERATURSENSOR MIT MANUELLER
TEMPERATUR-SOLLWERTEINSTELLUNG
TECHNISCHE DATEN
BESCHREIBUNG
Bei diesem Gerät handelt es sich um einen RF-(KNX) Funk-Temperatursensor zur Messung
der Temperatur, sowie einem eingebautem Drehwahlschalter zur manuellen
Temperatur-Sollwert-Einstellung.
Die Konfiguration des Sensors wird über einen Taster im inneren des Gerätes durchgeführt
(A). Das Gerät übermittelt den aktuell gemessenen Temperaturwert.
Die Verwendung des Sensors in der Nähe von funkbasierten Geräten oder Mikrowellen und
dergleichen ist nicht erlaubt. Der Abstand zwischen Sensor (Sender) und Empfänger sollte
mindestens 2m betragen.
BETRIEBSMODI
Der Sensor sendet den Temperaturwert unter folgenden Bedingungen:
1.- Der gemessene Temperaturwert hat sich seit der letzten Übertragung um mehr als
0,5°C verändert.
2.- Zyklisch.
3.- Durch kurzen Druck auf den Link-Taster (A).
Die Solltemperatur kann über den Drehwahlschalter eingestellt werden. Dieser Wert wird
anschließend über Funk übertragen.
Wenn der eingestellte Sollwert mit dem gemessenen Temperaturwert übereinstimmt,
leuchtet die rote Leuchtdiode für eine Sekunde auf. Wird das Stellrad auf „AUS“ gestellt,
wird vom Sensor das STANDBY-Telegramm versendet.
Sobald das Stellrad von der Position „AUS“ auf einen anderen Wert verstellt wird, versendet
der Sensor das AUTO-Telegramm per Funk.
Alle ~60 Minuten werden zyklisch die Telegramme „STANDBY / AUTO“ sowie der gewählte
Temperaturwert versandt.
VERLINKUNG
Um den Sensor mit einem anderen RF-(KNX)-Gerät zu verlinken (z.B. Funk-Thermostat-Ak-
tor) gehen Sie folgendermaßen vor:
1.- RF-(KNX)-Aktor in den Verlinkungs-Modus versetzen (siehe Bedienungsanleitung des
Aktors).
2.- Einlerntaste (A) des Sensors drücken und länger als eine Sekunde gedrückt halten.
3.- Prüfen Sie anschließend, ob die Verlinkung erfolgreich war. Weitere Informationen
hierzu finden Sie auch in der Bedienungsanleitung des Funk-Schaltaktors.
Lebensdauer >8 Jahre
Stromversorgung 1 Batterie 3V CR2450 (enthalten)
BITTE VOR BENUTZUNG DIE FOLIE AN DER BATTERIE ENFERNEN
A
A
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 676 311 rf at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 676 311 rf in the language / languages: English, German as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info