Manual Paladin 674 730 rf (page 2 of 2) (English, German)

683958

Zoom out

Zoom in

1/2

Workingtemperature -5ºC ~ +45ºC

Radio-Frequency 868,4MHz

Range

100m (in the freefield)

~30m (inside buildings)

1-CHANNEL BLINDS/SHUTTERS ACTUATOR OR

2-CHANNELS SWITCHING ACTUATOR

TECHNICAL DATA

DESCRIPTION

Wireless actuator for switching or controlling blinds/shutters compatible with the KNX-RF

Standard.

It has 2 output channels which allow to control one blind/shutter or to use them as a two

channels switching (ON/OFF) actuator.

It has 2 auxiliary inputs which allow to control also by two wired conventional pushbuttons.

MOUNTING AND INSTALLATION

A. Mounting:

• Place the actuator with the antenna as far away as possible from wires or metallic

surfaces.

• Move away the actuator from attenuations or interferences, for example from metallic

surfaces or other radio-frequency devices.

B. INSTALLATION:

Important: Switch off the power supply when installing!

B.1.– Wiring as 1-channel blinds/shutters actuator:

To roll up or down a blind, follow the wiring diagram of Fig 1.

Allows the connection of 2 wired buttons (P1 and P2), which permit the possibility of

controlling the load with two wired pushbuttons.

B.2.– Wiring as 2-channels switching actuator:

To control the switching ON and OFF of two diferent loads follow the wiring diagram of Fig 2.

Allows the connection of 2 wired buttons (P1 and P2), which permit the possibility of

controlling the load with two wired pushbuttons.

COMMISSIONING

• Programming selector switch:

P1: Programming Output 1 ‘R1’ (’Double Switch’ mode) or Blinds/Shutters actuator

(’Blinds control’mode).

P2: Programming Output 2 ‘R2’ (’Double Switch’ mode) or Blinds/Shutters actuator

(’Blinds control’ mode).

F: Standard working mode without Repeating function.

Rpt.: Standard working mode with Repeating function.

Rst.: Reset.

• Working mode selector switch:

1: ‘Blinds control’ mode.

2: ‘Double Switch’ mode.

Important: Changing operation mode lasts for ~ 10sec and involves the internal Reset of

the device.

• Programming LED key: links or deletes a sensor or actuator.

Programming a link between 674 730 rf (input channel) and a RF Sensor

To program a link between the input channel of the 674730rf and a RF transmitter device

(key, remote control, motion detector, touch screen ...):

1.- Turn the programming switch to position 'P1' or 'P2’:

• P1: to link the Load 1 in ‘Double Switch’ operating mode.

• P2: to link the Load 2 in ‘Double Switch’ operating mode.

• P1 or P2: to link the loads in ‘Blind control’ operating mode.

The green LED of the ‘Prog’ key will flicker slowly.

2.- Press briefly the ‘Prog’ key. The green programming LED must light up constantly.

3.- Set the RF sensor wich is going to be linked with the 674730rf in ‘link programming

mode’ according to its manual instructions.

4.- If the link is successful the green LED of the ‘Prog’ key will flicker slowly again. In this

case, place the programming selector switch to ‘F’.

If the link fails, the LED will remain constantly ON. In this case, place the selector switch

to ‘F’ and repeat all the process from step 1.

Auxiliary inputs 2 Inputs

Channels

Blinds/Shutters: 1 channel

Switch: 2 channels

Load capacity

2 x 16A

2 x 5A cosφ=0,5

Power supply 230V~ 50Hz

Programming a link between 674730rf (output channel) and a RF Actuator

To program a link between the output channel of the 674730rf and a RF actuator:

1.- Set the RF actuator in ‘link programming mode’.

2.- Turn the programming switch to position 'P1' or 'P2’:

• P1: to link the Output channel RF1 in ‘Double Switch’ operating mode.

• P2: to link the Output channel RF2 in ‘Double Switch’ operating mode.

• P1 or P2: to link the loads in ‘Blind control’ operating mode.

The green LED of the ‘Prog’ key will flicker slowly.

3.- Press briefly the ‘Prog’ key. The green programming LED will continue flickering.

4.- If the link is successful the green LED of the ‘Prog’ key will continue flickering slowly. In

this case, place the programming selector switch to ‘F’.

If the link fails, the green LED will remain constantly ON. In this case, place the selector

switch to ‘F’ an repeat all the process from step 1.

Reset. Delete all links

1.- Turn the programming selector switch to ‘Rst.’. The red LED of the ‘Prog.’ key will flicker

quickly.

2.- Keep pressing the ‘Prog.’ key for more than 5sec. After this time the red LED will remain

ON for 2sec and then it will flicker quickly again.

3.- Place the programming selector switch to ‘F’.

Enabling / Disabling the Repeating function

The repeater function can be used in installations where are communication problems

between RF devices.

The 674730rf must be installed in a location that provides cover for most part or all of the

installation RF devices.

To enable this function, place the programming selector to position 'Rpt.'.

Important: It is not recommended the use of more than two repeaters in a same installation.

Also, it is not recommended to use it unless necessary.

OPERATION

Blinds/Shutters control mode (1)

Action Operation

Brief press on P1

Receiving RF telegram:

"Step Up"

(a) If the blind is moving, stops

(b) If the blind is stopped, goes a step up

Sends a RF telegram "Step Up" if the action has been done

from the auxiliary pushbutton P1.

Brief press on P2

Receiving RF telegram:

"Step Down"

(a) If the blind is moving, stops.

(b) If the blind is stopped, goes a step down.

Sends a RF telegram "Step Down" if the action has been

done from the auxiliary pushbutton P2.

Sustained press on P1

Receiving RF telegram:

"Move Up"

(a) If the blind is moving down, stops and changes its

movement rolling the blind up for 3 minutes

(b) If the blind is stopped, it moves up for 3minutes

Sends a RF telegram “Move Up” if the action has been

done from the auxiliary pushbutton P1.

Sustained press on P2

Receiving RF telegram:

"Move Down"

(a) If the blind is moving up, stops and changes its

movement rolling the blind down for 3 minutes

(b) If the blind is stopped, it moves down for 3 minutes

Sends a RF telegram “Move Down” if the action has been

done from the auxiliary pushbutton P2.

Double Switch mode (2)

Action Operation

Brief or sustained press on

(a) If the Load 1 is OFF, it switches ON and sends the RF

telegram “ON” (RF output channel1)

(b) If the Load 1 is ON, it switches OFF and sends the RF

telegram “OFF” (RF output channel1)

Receiving RF telegram in the

channel 1: “ON”

Switch ON Load 1

Receiving RF telegram in the

channel 1: “OFF”

Switch OFF Load 1

Brief or sustained press on

(a) If the Load 1 is OFF, it switches ON and sends the RF

telegram “ON” (RF output channel 2)

(b) If the Load 1 is ON, it switches OFF and sends the RF

telegram “OFF” (RF output channel 2)

Receiving RF telegram in the

channel 2: “ON”

Switch ON Load 2

Receiving RF telegram in the

channel 2: “OFF”

Switch OFF Load 2

Fig. 3

Fig. 2

674 730 rf

Fig. 1

674 730 rf

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 674 730 rf in the language / languages: English, German as an attachment in your email.

The manual is 0,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Paladin 674 730 rf Manual

Product: