683933
1
Zoom out
Zoom in
Previous page
1/2
Next page
EA
E
S
R
P
Abb. 1 Abb. 2
Outputs 1 channel / 1 group
Dimming range 0, 10% ~ 100%
Control
Wirelessly (KNX-RF) and/or
Wired Pushbutton
Maximum number of pushbuttons Unlimited (without glow lamp)
Dimensions
Weight 35g
Working temperature 0ºC ~ +40ºC
Storage temperature -30ºC ~ +70ºC
Environmental protectio IP20 (EN60529)
According to the Standard EN60669-2-1
Connection terminals
“Lift” type.
Up to 6mm
2
wire
Radio-Frequency
Codified transmission in 868,4MHz
Range: 100m (in the free field)
Compatible with
RF-KNX Sensors: 676 010rf, 673 010rf,
670 010rf
46 x 46 x 30mm
GB
1-CHANNEL DALI WIRELESS RF-KNX DIMMER
TECHNICAL DATA
DESCRIPTION
Wireless dimmer switch for Fluorescence or LED lighting fixtures with DALI Ballast or Driver.
Compatible with RF-KNX media.
Unidirectional and Broadcasting communication. Individual addressing is not allowed.
Flush mounting into junction box.
Built-in dimming speed selector knob.
Compatible with the transmitters: 676 010rf, 673 010rf, 670 010rf.
Can also be controlled by a wired pushbutton:
· Brief press: switch on/off.
· Sustained press: dimming up/down.
Optional Memory function.
CHARACTERISTICS
Built-in mode selector knob (Fig. 1) for the link programming and commissioning:
· P: link programming.
· R: standard operation with repeater function.
· S: standard operation.
· E: one link deletion from the receiver channel.
· EA: all links deletion from the receiver and transmitter channel.
Dimming speed selector knob (Fig, 2):
· -: slow dimming speed.
· +: fast dimming speed.
Programming key “PROG” for the link process.
An external wired pushbutton can be installed for the local control of the load.
2 RF channels: output channel (wired pushbutton) and input channel (dimmer).
INSTALLATION
Install the dimmer according to the following steps:
1º - Switch the power supply off.
2º - Install the dimmer according to the wiring diagram Fig. 3.
3º - Switch the power supply on.
4º - Set the desired dimming speed.
WIRING DIAGRAM
NOTE: Do not forget to install the earth cable ( ) of the ballast or driver.
The connection of the external wired pushbutton is optional. It depends if the installation
requires wired pushbutton control or onle with a wireless transmitter.
DALI signal 16V Synchronized
Maximum number of equipments 64
Suitable type of lighting fixture DALI Ballasts or Drivers
Power consumption < 3W
Supply voltage 230V~ 50/60Hz
DALI
ECG
L
N
DA-
DA+
L
N
230V~ 50/60Hz
DALI
ECG
L
N
DA-
DA+
N
PDA+
DA-
L
No Mem
Mem
673834rf
230V~ 50/60Hz
Abb. 3
Ausgänge 1 Kanal / 1 Gruppe
Dimmbereich 0, 10% ~ 100%
Steuerung
via Funk (KNX-RF) und/oder
kabelgeb. Taster
Max. Anzahl kabelgebumdene Taster Unbegrenzt (unbeleuchtet)
Abmessungen
Gewicht 35g
Betriebstemperatur 0ºC ~ +40ºC
Lagertemperatur -30ºC ~ +70ºC
Schutzart IP20 (EN60529)
Angewandte Norm EN60669-2-1
Anschlussart Schraubklemmen (Aufzugsklemmen)
Funkfrequenz
Verschlüsselte Übertragung, 868,4MHz
Reichweite: 100 m (auf freiem Feld)
Kompatibel mit
Sender: 676 010rf, 673 010rf,
670 010rf
46 x 46 x 30mm
DE
1-KANAL DALI FUNK DIMMER (KNX-RF KOMPATIBEL)
TECHNISCHE DATEN
BESCHREIBUNG
Es handelt sich bei diesem Gerät um einen KNX-RF kompatiblen Dimmer / Schaltaktor für
Leuchtstoff- und LED-Lampen mit DALI Vorschaltgerät oder Treiber.
Unidirektionale- und Broadcast-Kommunikation. Einzeladressierung ist nicht möglich.
Geeignet für die Unterputzmontage.
Eingebauter Wahlschalter für die Dimmgewschwindigkeit.
Kompatibel mit folgenden Sendern: 676 010rf, 673 010rf, 670 010rf.
Der Aktor kann ebenfalls mit einem kabelgebundenen Taster gesteuert werden:
· Kurzer Tastendruck: EIN-/Ausschalten.
· Langer Tastdruck: Dimmen.
Optionale Memory-Funktion aktivierbar.
SYMBOLERKLÄRUNG / FUNKTION
Betriebsart-Wahlschalter (Abb. 1) für Verlinkung / Programmierung und Inbetriebnahme:
· P: Einlernvorgang / Programmiermodus.
· R: Normalbetrieb mit zusätzlicher Verstärker-Funktion (Repeater-Funktion).
· S: Normalbetrieb.
· E: Verlinkung trennen (Verlinkung zum Empfänger trennen).
· EA: Löschen aller Verlinkungen (Empfänger und Sender).
Wahlschalter für die Dimmgewschwindigkeit (Abb. 2):
· -: Langsame Dimmgeschwindigkeit.
· +: Schnelle Dimmgeschwindigkeit.
Einlerntaste „PROG“ für den Verlinkungs-/Programmiervorgang.
Ein Taster kann zur Steuerung der Lampen angeschlossen werden.
2 Funk Kanäle: Ausgangskanal (verdrahteter Taster) und Eingangskanal (Dimmer).
INSTALLATION
Bitte installieren Sie den Schaltaktor entsprechend nachfolgender Schritte:
1º - Vor Montage- und Installationsarbeiten Spannung freischalten
2º - Schließen Sie den Aktor entsprechend des Schaltplans (Abb. 3) an.
3º - Schalten Sie die Spannungsversorgung wieder ein.
4º - Stellen Sie die gewünschte Dimmgeschwindigkeit ein.
ANSCHLUSSPLAN
BITTE BEACHTEN: Schließen Sie Schutzerde / Schutzleiter ( ) an das
Vorschaltgerät oder den Treiber an!
Der Anschluss eines externen Tasters ist optional. Dies hängt davon ab ob in der Installation
ein kabelgeb. Taster oder ein Funksender gefordert wird.
DALI signal 16V synchronisiert
Maximale Anzahl EVG/Treiber 64
Geeignete Lasttypen DALI Vorschaltgeräte oder Treiber
Leistungsaufnahme < 3W
Anschlussspannung 230V~ 50/60Hz
673 834 rf
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 673 834 rf at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 673 834 rf in the language / languages: English, German as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info