683955
1
Zoom out
Zoom in
Previous page
1/2
Next page
672 730 rf
TECHNICAL DATA
ATTENTION: Dangerous voltage!.
Work with electrical equipment on the 230V mains must be carried out
exclusively by qualified technicians!.
Disconnect the mains voltage before proceeding to the assembly, disassembly
or manipulation of the electrical equipment!.
Power supply
Power consumption
Breaking capacity
Time delay
230V~ 50Hz
35mA
16A 250V cosφ=1
3sec ~ 10min
Radio-frequency
Mounting
Protection degree
Working Temperature
Dimensions
Compatible with
Codified transmission in 868,4MHz with
ERP>8mW and a coverage
of 100m (in the free field)
35mm DIN-rail
IP20
-10ºC ~ +45ºC
1 module wide (17,5mm)
RF-KNX: CH_Light_Actuator_Scene (0103h)
DE EN
WIRELESS 1-CHANNEL SWITCH
DESCRIPTION
It is based on a RF-KNX actuator which emulates the working mode of the channel code
CH_Light_Actuator_Scene 0x103.
It is composed by: LED (A), Time Selector (B), Commissioning Pushbutton (C) and
Working Mode Selector Switch (D).
CHARACTERISTICS
Working mode selector switch for the setting-up and commissioning:
- B: delete a link from the receiver channel.
- P: link programming of the transmitter or receiver channel.
- F: normal operation.
- A: normal operation with repeater function.
- R: delete all links from the transmitter and receiver channels.
Operation as impulse relay or time switch.
Possibility of working as RF signals repeater.
Possibility of wiring an additional wired pushbutton to:
- Local control of the load connected to the device.
- Remote control, via RF, of one or several linked receivers.
Compatible with ISO-IEC 14543-2 KNX protocol. Two objects:
- The auxiliary pushbutton answers to the object CH_PB_Toggle 0x02.
- The actuator answers to the object CH_Light_Actuator_Scene 0x103.
INSTALLATION
Install the actuator according to the wiring diagram.
The auxiliary pushbutton (E) is optional. It depends on if the installation requires a local
control for the load connected to the Switch or if it is necessary to control remotely other
linked RF-KNX devices.
WORKING MODES
A.- Operation with the external Pushbutton (E)
Any short press (<300msec) of the pushbutton has as the effect of:
- The change of the previous state of the load connected to the Switch: ON or OFF.
- The transmission of an ON or OFF message, in concordance with the change of the
load. The messages are compatible with the RF-KNX object ‘CH_PB_Toggle 0x02’
(0002h).
B.- Operation through its receiver channel
The load connected to the Switch can be controlled remotely with a RF transmitter.
The accepted messages are compatible with the RF-KNX object
‘CH_Light_Actuator_Scene’ 0x103.
TECHNISCHE DATEN
FUNK-SCHALTAKTOR 1-KANAL
ACHTUNG: Gefährliche Spannung!.
Arbeiten mit elektrischen Geräten am 230V Netz dürfen nur von qualifiziertem
Fachpersonal durchgeführt werden!.
Trennen Sie die Netzspannung, bevor Sie mit der Montage, Demontage oder
Manipulation der elektrischen Geräte beginnen!.
Stromversorgung
Leistungsaufnahme
Schaltleistung
Ausschaltverzögerung
230V~ 50Hz
35mA
16A 250V cosφ=1
3sec ~ 10min
Funkfrequenz
Montage
Schutzart
Betriebstemperatur
Abmessungen
Kompatibel mit
Verschlüsselte Übertragung,
868,4MHz, ERP > 8 mW,
Reichweite: 100m (auf freiem Feld)
35mm DIN-Schiene
IP20
-10ºC ~ +45ºC
1 TE (17,5mm)
RF-KNX: CH_Light_Actuator_Scene (0103h)
BESCHREIBUNG
Es handelt sich bei diesem Gerät um einen KNX-RF kompatiblen Schaltaktor, der die
Betriebsart der Kanalkennung „CH_Light_Actuator_Scene 0x103“ emuliert.
Anzeige und Einstellmöglichkeiten:
(A) Anzeige-LED
(B) Zeit-Wahlschalter
(C) Einlerntaste
(D) Betriebsart-Wahlschalter
SYMBOLERKLÄRUNG / FUNKTION
Betriebsart-Wahlschalter (D):
- B: Verlinkung trennen (Verlinkung zum Empfänger trennen)
- P: Einlernvorgang / Programmiermodus (Empfänger oder Sender)
- F: Normalbetrieb
- A: Normalbetrieb mit zusätzlicher Verstärker-Funktion (Repeater-Funktion)
- R: Löschen aller Verlinkungen (Empfänger und Sender).
Betrieb als EIN/AUS-Schalter oder Impuls-Relais möglich.
Optional als RF Signal-Verstärker verwendbar.
Zusätzlich ist der Anschluss eines externen Tasters möglich:
- Zur Steuerung des an den Aktor angeschlossenen Verbrauchers
- Zur Steuerungeines oder mehreren (via Funk) verlinkten Empfänger
Kompatibel mit dem ISO-IEC 14543-2 KNX-Protokoll:
- Der externe Eingang kommuniziert mit dem Objekt “CH_PB_Toggle 0x02“
- Der Schaltaktor kommuniziert mit dem Objekt „CH_Light_Actuator_Scene 0x103“.
INSTALLATION
Montieren Sie den Funk-Schaltaktor gemäß des dargestellten Schaltplans. Der
Anschluss eines externen Tasters (E) ist optional. Abhängig von der Anwendung kann
der, an den Aktor angeschlossenen Verbraucher gesteuert werden. Alternativ können
mit dem Schaltaktor (via Funk) verlinkte Geräte gesteuert werden.
BETRIEBSMODI
A.- Betrieb mittels externem Taster (E)
Eingabe über externen Taster (<300msec):
- Der Schaltzustand des Schaltaktors ändert sich: ON oder OFF.
- Gemäß der Änderung des Schaltzustands des Schaltaktors wird ein ON/OFF Signal
gesendet. Das gesendete Signal ist mit folgendem KNX RF Objekt kompatibel:
“CH_PB_Toggle 0x02“ (0002h).
B.- Betrieb als RF-Empfänger
Die an dem Schaltaktor angeschlossene Last kann per Funk mittels einem RF-Sender
gesteuert werden. Folgendes KNX RF Objekt ist kompatibel: “CH_Light_Actua-
tor_Scene” 0x103.
min
INT
3s
1
3
5
10
min
A
C
B
D
R
P
F
A
B
L
N
230V~ 50Hz
E
5 6
3 4
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 672 730 rf at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 672 730 rf in the language / languages: English, German as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info