612982
3
Zoom out
Zoom in
Previous page
1/24
Next page
ISIMAT+
MOTION DETECTOR
INSTRUCTIONS ON USE
DESCRIPTION
The ISIMAT+ motion detector detects invisible infrared radiation from
people and other heat sources without emitting any form of radiation.
When a heat source moves in front of the ISIMAT+, its output circuit is
activated and when it no longer detects the movement, it will deactivate
after an adjustable delay.
The ISIMAT+ reacts in this way only when ambient light conditions are
below the selected level.
INSTALLATION
WARNING: The assembly and installation of the electric apparatus must
only be carried out by an authorised installer.
ALL POWER MUST BE SWITCHED OFF PRIOR TO COMMENCING
INSTALLATION WORK
The apparatus is fitted with an internal security circuit that protects it
against electromagnetic interference. However, certain especially strong
magnetic fields could affect its operation and therefore, it must not be
installed close to inductive loads (motors, transformers, telephony
antennas, transformer substations and industrial machinery etc).
MOUNTING
It is wall-mounted, but highly reflective surfaces (liquids and marble etc),
elements subject to sudden changes in temperature (heating and air-
conditioning and possible air currents) and also light sources must be
avoided within its detection area.
Remove the base cover by loosening the screw located in the lower
section of the unit.
Mount the base cover where the unit is to be installed.
The ideal mounting height is between two and three metres and the
direction of movement of possible heat sources should be transversal to
the ISIMAT+ lens.
It must be taken into account when installing the ISIMAT+ that detection
takes place when the detection beams are crossed; therefore, if the heat
source to be detected is moving parallel to the beams, detection will be
produced at a smaller distance since it will not cross the beams until it is
very close to the apparatus.
In the above figures, the arrow indicates direction of movement of the
person or object to be detected.
The ambient temperature where the ISIMAT+ is installed can significantly
affect detection sensitivity and hence, the detection distance. Higher
temperatures means reduced sensitivity because the apparatus operates
by detecting the movement of a heat source (in most cases, this
temperature is 36 ºC, that of the human body), the closer the ambient
temperature is to 36 ºC, the poorer the detection.
CONNECTION
The unit should be connected in accordance with the following diagram:
Fit the ISIMAT+ to the base and secure it with the screw.
PUTTING INTO OPERATION: ADJUSTMENTS
There are two controls on the ISIMAT+ sphere:
ADJUSTING THE DETECTION FIELD
The head is able to rotate horizontally by approximately 180º (do not
attempt to force rotation beyond 180º) and vertically by approximately 45º,
thus moving the detection area as shown in the figure:
LOWEST SENSITIVITYHIGHEST SENSITIVITY
DO NOT EXOPOSE
TO SUNLIGHT
DO NOT INSTALL
CLOSE TO LAMPS
DO NOT INSTALL
OVER
HEAT SOURCES
DELAY TIME
ADJUSTMENT
AMBIENT LIGHTING
LEVEL ADJUSTMENT
2,5 m.
6 m.
12 m.
12
6
8
6
Area of highest
sensitivity
ISIMAT+
Detection
angle 200 º
L' N L
L
N
L' N L
230 V AC
Light
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Orbis ISIMAT plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Orbis ISIMAT plus in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info