Manual Orbis DATA LOG 2 plus (page 5 of 10) (English, German, Italian, Spanish)

612892

Zoom out

Zoom in

1/10

DATA LOG + / DATA LOG 2+

DIGITAL TIME SWITCH

INSTRUCTIONS FOR USE

DATA LOG + / DATA LOG 2 + is a digital time switch designed for controlling any

electrical installation. It includes the possibility of carrying out short-duration or

pulsed operations (from 1 to 59 seconds), On and Off at a set time, repetitive

cycles (from 1 minute to 99 hours, 59 minutes), automatic summer/winter time

change, holiday (day/month) period, adjustable screen brightness and updating

from an infrared remote control. All these features can be applied to channel C1,

and to C2 if DATA LOG 2+ is used.

Function menus can appear in several languages and they display a chronogram

on screen that shows the programming for the current day.

To view the chronogram, as well as the other unit configurations, it is only

necessary to repeatedly press the

key (info) until the desired display is

obtained.

DATA LOG + has one independent voltage-free switched circuit that allows the

programming of up to 70 operations.

DATA LOG 2+ has 2 independent voltage-free switched circuits that allow the

programming of up to 70 operations between channel 1 and/or channel 2.

INSTALLATION

WARNING: installation and mounting of electric apparatus shall be carried out by

an authorised installer.

ALL POWER MUST BE REMOVED BEFORE PROCEEDING WITH THE INSTALLATION,

The unit is internally protected from interference by a safety circuit. However,

certain particularly strong fields can alter its operation. Interference can be avoided

if the following installation rules are followed:

- The unit should not be installed next to inductive loads (motors, transformers and

contactors etc.)

- It is recommended to provide a separate line for the supply (if necessary,

equipped with a mains filter).

- Inductive loads must be fitted with interference suppressors (varistor, RC filter).

If the time switch is used in combination with other units at an installation, it is

necessary to check that the assembly so formed does not generate parasitic

interference.

THE POWER SHALL ONLY BE RESTORED WHEN THE EQUIPMENT IS COMPLETELY

INSTALLED.

MOUNTING

Electronic control device for independent installation in distribution cabinet fitted

with symmetrical 35 mm profile in accordance with the standard EN 60715 (DIN

Rail EN 60715 (Rail DIN).

CONNECTION

Connect the mains supply according to the following schematic:

The Line and Neutral position must be respected, checking the connections made.

A wrong connection can destroy the unit.

PUTTING IN SERVICE

For the device to be able to execute control over the installation, IT MUST BE

POWERED UP.

The display will light up and the MAIN screen will appear.

When the equipment is switched off, the screen will also be off, but the date, time

and all programming will be maintained during the four-year lifetime of the

incorporated lithium battery.

In this case, if any key is pressed, the display will temporarily switch on to allow

programming. If no keys are pressed during fifteen seconds, the display will be

switched off again.

These units have an LCD panel and four keys for adjustment and programming.

The following information is shown on the LCD:

 Day of the week in text line 1 in the ON state

 Complete time and date

 Symbol

= Vacation state

 Chronogram with the operations for that day

 State of circuits C1 / C2: ON

, OFF

 INFO symbol

 PERMANENT text in line 2 (if activated)

 OFF text in line 1 (if in switched-off state)

 LOG technology: two text lines for programming help menus

 Two lines of text in programming help menu style and a chronogram with

48 divisions in which each segment represents thirty minutes

CONFIGURATION

DATA LOG +/ DATA LOG 2+ units leave the factory configured with the current

date and time, and configured as follows:

Hour Mode: 24 h

W-S Change Automatic (last Sunday of March)

S-W Change Automatic (last Sunday of October)

Vacations: NO (deactivated)

Programs: None (memory empty)

PROGRAMMING

The programming is based on menus and submenus through which we can move

to program operations or make adjustments to the unit. Access to the main menu

from the idle screen is by pressing key . Use the ▼ and ▲ keys to step through

the different menus, which can be entered by pressing key . To go back to the

previous menu, press key C.

The data to be entered always appear flashing on the screen.

The structure of the menus is the following:

MAIN MENU

 PROGRAMS. This is the menu where the different operations are programmed.

There are 70 memory slots (from PROG_01 to PROG_70).

o ENTER. Where we will edit the different programs. With the ▼ and ▲ keys,

we can step from PROG_01 to PROG_70. After selecting one, it is entered

by pressing . Once inside the program, we have the following options:

- EDIT. The message “PROG_01: EDIT” is shown on screen. By

validating with  TYPE C1: ON appears on screen. The type of

operation for the DATA LOG is selected with the ▼ and ▲ keys: C1:

ON, C1: OFF, C1: PULSE, C1: CYCLE. In the case of DATA LOG 2+,

we also have C2: ON, C2: OFF, C2: PULSE, C2: CYCLE. The choice

made is validated with key . Next the hour, minute and combination of

days of the week are chosen for the operation.

In the case of PULSES, it will be necessary to specify the pulse

duration in seconds.

In the case of CYCLES, it is necessary to specify when the cycle will

begin (hour, minute and day of the week); and then, when the cycle

finishes (hour, minute and day of the week). To end the CYCLE

definition, it would only remain to indicate the ON period and the OFF

period respectively (in hours and minutes).

- COPY. It copies the operation of a program for use in another.

- PASTE. It pastes the previously copied operation.

- ERASE. It deletes the selected program.

o ERASE. It allows a deletion to be carried out of all the operations in the

programs in one step.

 CLOCK. This will set the equipment time. The variables to be configured are (in

this order): year, month, day, hour and minute. The day of the week is

automatically calculated.

 PERMANENT. This is the menu in which we can fix a permanent operation (On

/ Off) of channel C1, and of channel C2 in the case of DATA LOG 2+. With the

▼ and ▲ keys we step through the different options: C1: YES  C1: NO  C2:

YES  C2: NO. We validate the case we want with . The equipment will not

follow the operations programming for the selected channel if OPTION YES is

selected.

The contact position can be changed manually.

 LANGUAGE. This is the menu where the unit language is set.

 SETTINGS. This is the menu in which most of the unit configurations can be

carried out.

o SEASON. It establishes the time change mode Summer - Winter and Winter

- Summer.

- AUTO. It automatically carries out the time change on the last Sunday of

March and on the last Sunday of October.

- MANUAL. It allows the day and time to be chosen for carrying out the time

change.

- DESACT. The time change is not carried out.

DAY OF THE WEEK

CHRONOGRAM

INFO SYMBOL

DATE

CURRENT TIME

HOLIDAY

SYMBOL

INFO SYMBOL

CIRCUIT 2

STATUS

STANDBY STATUS DISPLAY

C1 (INFO) STATUS DISPLAY

CIRCUIT 1

STATUS

654

C1 1 - 2

C2 4 - 5

1 N

DATA LOG + DATA LOG 2+

OPEN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Orbis DATA LOG 2 plus in the language / languages: English, German, Italian, Spanish as an attachment in your email.

The manual is 0,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Orbis DATA LOG 2 plus Manual

Product: