677276

ONYX STWM711 - 179.185 Manual

5
Zoom out
Zoom in
Previous page
1/24
Next page
5
OPERATION
Turn off the system first, turn down the receivers volume to the minimum and then turn on the receiver, CPU initializes, the LCD
screen begins to display and the system reverts to the last shutdown’s state!
If the system is turned on look at the transmitter and receiver’s frequency.Then the receiver display shows RF signal level value,
the antenna status will display antenna A or B. Adjust the volume to the desired level.
Volume adjustment
Adjust the receiver’s volume to the 12 o’clock position, then adjust the volume of the amplifier or mixer to a desired level. If the
receiver volume has been adjusted too loud the amplifier will produce a saturated distortion which will blow the amplifier or/and
the loudspeaker(s)!
Best acoustics:
1. You should always see the receiver antenna from your transmitter location.
2. The distance between transmitter and receiver should be as short as possible.
3. If the receiver has two antennas, they should be adjusted 45° with a vertical line.
4. Keep the antennas away from metal surfaces and shelter.
5. Let the antennas not contact or cross each other.
6. Before using the system during the presence of public do a test to find out where the “dead spots” are. Avoid these
spots when operational
TROUBLESHOOTING
PROBLEM
INDICATOR
SOLUTION
No sound
Red transmitter indicator is not flash
Slide transmitter POWER ON/OFF
switch to ON position. Make sure battery
is inserted properly, observing battery (+
/ -). If battery is inserted properly,
replace with fresh battery.
No sound
Red transmitter indicator is flash.
Slide transmitter MUTE/ON switch to
ON position.
No sound
Red receiver indicator POWER light off.
Make sure AC adapter is securely
plugged into electrical outlet and into DC
input connector.
Make sure AC electrical outlet works
and supplies proper voltage.
No sound
Receiver signal indicators A/B lights
glowing.
Turn up receiver volume control.
Confirm that the output connections
from the receiver to the external
equipment are secure.
Sound level differs from level of a
cabled instrument.
Receiver signal indicators A/B lights
glowing.
Adjust transmitter gain level to
compessary.
Adjust receiver volume as necessary.
Distortion level increases gradually
Receiver signal indicators A/B lights and
transmitter LOW BATTERY light
glowing
Replace transmitter battery
Bursts of noise or other audible
radio signals present.
Signal indicators A/B/ lights on.
Identify potential sources of
interferences (other RF-sources) and
turn off, remove or use a wireless
system operating on a different
frequency.
Momentary loss of sound as
transmitter is moved around
performing area.
Receiver signal indicator A/B lights of
when sound is lost
Reposition receiver and perform walk-
through test again. If audio dropouts
persist, mark “dead” spots and avoid
them during performance.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ONYX STWM711 - 179.185 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ONYX STWM711 - 179.185 in the language / languages: English, German, Dutch, Spanish as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info