517113
71
Zoom out
Zoom in
Previous page
1/72
Next page
71
Troubleshooting guide
VIDEO and AUDIO
Desired picture does not appear.
Improper connection.
Check the connection again. Insert the plugs and connectors
completely.
No OSD Menu display.
Improper connection.
Check connections.
OSD Menu is displayed when monitor is connected to VIDEO or
S VIDEO of MONITOR OUT.
Confirm connections (see page 18).
No sound, or sound of the selected source is not heard.
Input Setup menu settings are incorrect.
Check settings (see page 33).
No picture appears on the TV screen (or monitor).
TV (or monitor) is not set to receive the output signals from the
receiver.
Set the TV (or monitor) to the receiver input.
Video cable is not connected securely.
Check connections.
You have connected to the COMPONENT VIDEO connectors
but the TX-DS898 is not set properly.
Check the Video Setup submenu of the Input Setup menu
(page 35).
REMOTE CONTROLLER
Front panel controls function but remote controller
controls do not.
No batteries in remote controller.
Insert batteries.
Batteries have worn out.
Replace batteries.
Remote controller is not pointed at the remote sensor of the TX-
DS898.
Point the remote controller at the remote sensor of the TX-
DS898.
Remote controller is too far from the TX-DS898.
Operate the remote controller within 5 meters (16 feet).
Remote controller is functioning in a different mode
Press the RCVR MODE button.
OTHER
LATE NIGHT function cannot be used.
Playback source is not Dolby Digital encoded.
Check that the DOLBY DIGITAL indicator lights up on the
display.
Re-EQ function cannot be used.
Listening mode is set to Theater-Dimensional, THX, or Direct/
Pure Audio.
See page 43.
Parameter cannot be set for Front Effect etc.
Parameter may not be able to be set depending on the listening
mode.
See table on page 43.
If one of the messages shown below appears
Not available with headphones use
The operation is not allowed because headphones are plugged into
the TX-DS898.
Not available with Multichannel use
Cannot be used while the multi-channel output is being used.
Not available in this Sp Config
Will not work with the current speaker configuration settings.
Not available in Zone 2 mode
The operation is not allowed because the Zone 2 mode is turned on.
Only available with Dolby D
No setting other than Dolby Digital can be set.
Not available in this Listening mode
Will not work with the current listening mode.
Not available with this signal
The listening mode cannot be selected with the current input source.
Powerd Zone 2 is not Activated
Will not work with the Zone 2 output set to non-activated (Not
Activated).
Not available with Muting
Will not work because the muting is activated.
Zone 2 is not On
Will not work because the Zone 2 has not been turned on.
Multichannel audio is not output.
To listen to multichannel audio, Yes must be selected in the
Multichannel in the Multichannel setup sub-menu of the Input
Setup menu. Also, it is necessary to select Multichannel with the
AUDIO SELECTOR button.
Check that the component is connected to the MULTI
CHANNEL INPUT port and check the Setup menu settings.
Components in remote zone (Zone 2) do not operate
properly.
Components are incorrectly connected.
Check connections.
Objects are interfering with remote controller signals.
Move inferring objects away from path of remote controller
signals.
Also refer to the respective instruction manuals of the compact disc
player, DVD player, video cassette recorder, TV monitor, etc., that
compose your entertainment system.
The TX-DS898 contains an internal microcomputer that performs
high-level operations. However, on extremely rare occasions, noise
or interference from an external source or static electricity may cause
faulty operation. If this occurs, unplug the power cord from the wall
outlet, wait five or more seconds, and then plug it back in. This
should correct the situation.
* To reset the surround mode and other settings to the factory
default settings, hold down the VIDEO 1 button with the TX-
DS898 turned on and then press the STANDBY/ON button.
CLEAR appears in the front display and the TX-DS898 enters
the standby state.
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-DS898 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-DS898 in the language / languages: English as an attachment in your email.

The manual is 2,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info