601422
152
Zoom out
Zoom in
Previous page
1/156
Next page
152
Troubleshooting
—Continued
Not available with Headphones use
Operation not allowed while a pair of headphones is con-
nected.
Not available in this Sp Cong
Doesnt work with the current speaker conguration.
Only available with Dolby D
Can be used with only Dolby Digital.
Not available with this signal
Doesnt work with the current listening mode.
Not available with Muting
Operation not allowed because the RDC-7.1 is currently
muted.
Not available in this Listening Mode
Doesnt work with the current listening mode.
Not available with NET AUDIO use
Operation not possible with Net Audio selected for the
input source.
Not available with Dolby Headphone Off
Doesnt work with the Dolby Headphone function off.
Not available with Dolby Headphone On
Doesnt work with the Dolby Headphone function on.
Not available with zone2 out in Line out
Operation not possible with 1-8. f. Zone 2 Out set to
Line Out.
Not available with zone3 out in Line out
Operation not possible with 1-8. g. Zone 3 Out set to
Line Out.
Specications
USA and Canadian models
General
Error Messages
Memory backup
The RDC-7.1 uses a battery-less memory backup sys-
tem in order to retain radio presets and other settings
when it is unplugged or in the case of a power failure.
Although no batteries are required, the RDC-7.1 must
be plugged into an AC outlet in order to charge the
backup system.
(On other than USA, Canadian, and Australian models,
the RDC-7.1’s Power switch must be set to On in order
to charge the backup system). Once it has been
charged, the RDC-7.1 will retain the settings for several
weeks, although this depends on the environment and
time will be shorter in humid climates.
The RDC-7.1 contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
To reset the RDC-7.1 to its factory defaults, turn it on
and, while holding down the [Video 1] button, press the
[Standby/On] button. When the reset is complete,
“CLEAR” appears on the display and the RDC-7.1
enters Standby mode.
Onkyo is not responsible for damages (such as CD rental
fees) due to unsuccessful recordings caused by the
unit’s malfunction. Before you record important data,
make sure that the material will be recorded correctly.
Power Supply Rating: AC 120 V, 60 Hz
Consumption Power: 1.0 A
Standby Power Consumption: 3.9 W
Dimensions (W
×
H
×
D): 17 11/16"
×
7 3/4"
×
18 13/16"
(450
×
197.3
×
477.1 mm)
Weight: 45.6 lbs (20.7 kg)
Inputs:
Audio
Multichannel (7.1ch) Inputs: 1 or 2 (option)
Phono (MM): 1
Line inputs: 9 (assignable)
Digital inputs Coaxial: 6
Digital inputs Optical: 6 (assignable)
Digital inputs AES/EBU 1 (option)
Video (Option)
Composite Video inputs: 6 (assignable)
S Video inputs: 6 (assignable)
Component Video RCA
inputs: 3 or 4
Component Video BNC
input: 1
Audio and Video
HDMI inputs (19-pin): 2 (option)
Miscellaneous
IR in (phoenix connector): 3 (for Main, Zone 2 and Zone 3)
Outputs:
Audio
Balanced Pre out A: Front L/R, Center, Surround L/R,
Surround Back L/R, Subwoofer
Unbalanced Pre out A: Front L/R, Center, Surround L/R,
Surround Back L/R, Subwoofer
Unbalanced Pre out B: Subwoofer
Headphones: 1
Line outputs: 5 (assignable to Recout, Zone 2 out
and Zone 3 out)
Digital outputs Coaxial: 2 (assignable to Recout, Zone 2 out
and Zone 3 out)
Digital outputs Optical: 2 (assignable to Recout, Zone 2 out
and Zone 3 out)
Video (Option)
Composite Video outputs: 3 (assignable to Monitor out A/B,
Recout, Zone 2 out and Zone 3 out)
1 (xed, Monitor out A)
S Video outputs: 3 (assignable to Monitor out A/B
and Recout)
1 (xed, Monitor out A)
Component Video RCA
outputs: 1 or 2
Component Video BNC
output: 1
Audio and Video
HDMI output (19-pin): 1
Miscellaneous
12V Trigger out (phoenix
connector): 5 (for A, B, C, D, E)
Inputs/Outputs:
Miscellaneous
i. LINK(AUDIO) (4 pin): 2
Ethernet (Net-Tune): 1 (option)
(1/8-inch mini-jack):
1
RS232 (9 pin D-SUB
Female connector): 1
Antennas:
FM: 75 ohms unbalanced
AM: Included loop antenna and external
terminal
AC Inlet: 1 (IEC type)
152


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo RDC-7.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo RDC-7.1 in the language / languages: English as an attachment in your email.

The manual is 12,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo RDC-7.1

Onkyo RDC-7.1 User Manual - German - 156 pages

Onkyo RDC-7.1 User Manual - Dutch - 156 pages

Onkyo RDC-7.1 User Manual - French - 156 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info