673473
1
Zoom out
Zoom in
Previous page
1/4
Next page
1. Busque el código correspondiente a su aparato (por ejemplo Televisión
A
ccent) en la lista de códigos. Los códigos aparecen ordenados por tipo de
aparato y marca. Los códigos más populares aparecen en primer lugar.
A
segúrese de que el aparato esté encendido (no en modo de espera).
2
. Pulse y mantenga pulsada la tecla SETUP hasta que el LED rojo debajo de
la tecla POWER parpadee dos veces (el LED rojo parpadeará una vez
p
rimero, y a continuación dos).
3
. Introduzca el código del aparato de cuatro
dígitos utilizando las teclas numéricas (por ejemplo código Accent 0037).
E
l LED rojo se encenderá de forma intermitente dos veces para confirmar
que el código ha quedado guardado.
4. Ahora, apunte con el ONE FOR ALL a su aparato y pulse OFF. Si el
a
parato se apaga, el ONE FOR ALL ya está preparado para funcionar con
su aparato. En caso de que no sea así, repita los pasos 1-5 empleando
otro código de la lista que corresponda a la marca.
Si ninguno de los códigos de la lista para su marca logra que funcione su
a
parato O si la marca no aparece en la lista, pruebe el método de búsqueda.
El Método de Búsqueda le permite buscar el código para su aparato reali-
zando una búsqueda entre todos los códigos que contiene la memoria del
ONE FOR ALL. El Método de Búsqueda también puede resultar útil si la
marca en cuestión ni siquiera aparece en la lista.
1. Asegúrese de que el aparato esté encendido (no en modo de espera).
2. Pulse y mantenga pulsada la tecla SETUP hasta que el LED rojo debajo de
la tecla POWER parpadee dos veces (el LED rojo parpadeará una vez pri-
mero, y a continuación dos).
3. Pulse 9 9 1. El LED rojo parpadeará dos veces.
4. A continuación, pulse POWER.
5. Apunte con el ONE FOR ALL hacia el televisor. Ahora pulse Channel + una y
otra vez, hasta que se apague el televisor (cada vez que se pulsa la tecla
Channel +, el ONE FOR ALL enviará una señal de CONEXIÓN desde el
siguiente código de la memoria). Podría llegar a pulsar esta tecla muchas
veces (hasta 150), de modo que sea paciente.
6. Tan pronto como el televisor se apague, pulse la tecla SETUP para
almacenar el código.
Método de búsqueda
Configuración de códigos
(
Ejemplo: configuración del MANDO A DISTANCIA ONE FOR ALL
p
ara la televisión)
E
SPAÑOL
Su mando a distancia One For All puede aprender cualquier función de otros
mandos a distancia. Para ello, debe tener a mano todos los mandos a distancia
originales y asegurarse de que tengan pilas. Para programar funciones, el
mando original debe estar aproximadamente a 3 cm del mando OFA,
apuntando hacia él como se muestra abajo:
1. Pulse y mantenga pulsada la tecla SETUP hasta que el LED rojo debajo de
la tecla POWER parpadee dos veces (el LED rojo parpadeará una vez
primero, y a continuación dos).
2. Pulse 9 7 5.
3. Pulse y suelte el botón que quiere que aprenda la función (por ejemplo,
el botón de encendido TV): el LED rojo parpadeará continuamente.
Aprendizaje
2 - 5 CM
GUIDE
E
SPAÑOL
4. Pulse y suelte el botón correspondiente en el mando a distancia original,
p
or ejemplo, Encender.
5
. El LED rojo parpadeará dos veces para indicar que ha aprendido la función
correctamente.
6. Repita los pasos 3 y 4 para cada botón que quiera aprender; recuerde que
p
uede aprender botones de distintos mandos a distancia, pero solo una
función por botón.
7. Cuando haya programado todos los botones que necesite, mantenga
p
ulsado el botón SETUP hasta que el LED rojo parpadee dos veces.
Si el LED rojo emite un parpadeo largo en el paso 5, el mando no
h
a aprendido la función correctamente; debe empezar desde el paso 3.
Si observa que uno o más botones no funcionan correctamente después
de la configuración, puede acceder de nuevo al modo de aprendizaje en
c
ualquier momento repitiendo el proceso desde el paso 1.
Anulación de una función memorizada para obtener la función
o
riginal
1. Pulse y mantenga pulsada la tecla SETUP hasta que el LED rojo debajo de
l
a tecla POWER parpadee dos veces (el LED rojo parpadeará una vez
primero, y a continuación dos).
2. Pulse 9 7 6.
3
. Pulse dos veces la tecla que desea anular (p. ej., el roja).
Accent
Accent
AAA
AAA
1. Ermitteln Sie den Code für Ihr Gerät (z.B. Accent Fernsehgerät) in der
C
odeliste. Die Codes sind nach Gerätetyp und Markenname aufgelistet.
Die häufigsten Codes sind zuerst aufgeführt. Achten Sie darauf, dass Ihr
G
erät eingeschaltet ist (nicht in Standby).
2
. Drücken und halten Sie die Taste SETUP gedrückt, bis die rote LED unter
der POWER-Taste zweimal blinkt (die rote LED blinkt einmal, dann zweimal).
3. Geben Sie den ersten für Ihren Gerätetyp und Ihre Marke aufgeführten
C
ode ein (z.B. TV Accent = 0037)
4
. Richten Sie die ONE FOR ALL auf Ihr Gerät und drücken Sie POWER
(AN/AUS Taste). Wenn das Gerät abschaltet, ist die ONE FOR ALL für
d
ie Bedienung Ihres Geräts bereit.
W
enn keiner der für Ihre Marke aufgeführten Codes funktioniert versuchen
Sie bitte den Code Suchlauf. Der Code Suchlauf ist auch brauchbar, wenn Ihre
Marke überhaupt nicht aufgeführt ist.
M
it den Code Suchlauf können Sie den Code für Ihr Gerät herausfinden, in
dem Sie alle Codes durchsuchen, die im Speicher der ONE FOR ALL
enthalten sind. Den Code Suchlauf kann auch funktionieren, wenn Ihre
Marke Überhaupt nicht aufgefürt ist.
1. Schalten Sie Ihr Fernsehgerät ein (Standby genügt nicht).
2. Drücken und halten Sie die Taste SETUP gedrückt, bis die rote LED unter
der POWER-Taste zweimal blinkt (die rote LED blinkt einmal, dann zweimal).
3. Drücken Sie 9 9 1. Die rote LED blinkt zweimal.
4. Drücken Sie dann POWER.
5. Richten Sie die ONE FOR ALL auf Ihr Fernsehgerät. Drücken Sie dann CH+ immer
wieder, bis das Fernsehgerät abschaltet (jedes Mal, wenn Sie die Taste CH+
drücken, sendet die ONE FOR ALL ein POWER-Signal aus dem nächsten Code im
Speicher). Möglicherweise ssen Sie die Taste sehr oft dcken (bis zu 150 Mal);
haben Sie also bitte Geduld.
6. Wenn Ihr Fernsehgerät ausschaltet, drücken Sie die Taste SETUP, um den
Code zu speichern.
Code Suchlauf
Einstellen der Codes
(Beispiel: So programmieren Sie die ONE FOR ALL-FERNBEDIENUNG
f
ür Ihr Fernsehgerät)
D
EUTSCH
D
EUTSCH
1. Trouvez le code de votre appareil (p. ex. téléviseur Accent) dans la liste
d
es codes.
Les codes sont répertoriés par type d’appareil et par nom de marque.
L
e code le plus courant apparaît en premier. Vérifiez que votre appareil
est allumé (et non en veille).
2. Enfoncez et maintenez la touche SETUP jusqu’à ce que la DEL rouge sous la
t
ouche POWER clignote deux fois (la DEL rouge clignote une fois puis deux
fois).
3. Entrez votre code d’appareil à quatre chiffres avec les touches
n
umériques (p. ex. le code Accent 0037). La DEL rouge clignote deux fois
pour confirmer l’enregistrement du code.
4. Maintenant, pointez la ONE FOR ALL vers votre appareil et appuyez sur
O
FF. Si votre appareil séteint, la ONE FOR ALL est prête à l’utiliser. Si les
fonctions n’agissent pas correctement, répétez les étapes 1 à 5 en utilisant
un autre code répertorié sous votre marque.
Si aucun des codes répertoriés pour votre marque n’actionne votre appareil,
O
U si votre marque nest pas listée, essayez la méthode de recherche.
La méthode de recherche vous permet de rechercher le code de votre
appareil en parcourant tous les codes contenus dans la mémoire de la ONE
FOR ALL. La méthode de recherche peut fonctionner même si votre
marque n’apparaît pas dans la liste.
1. Allumez votre téléviseur (pas en veille).
2. Enfoncez et maintenez la touche SETUP jusqu’à ce que la DEL rouge sous
la touche POWER clignote deux fois (la DEL rouge clignote une fois puis deux
fois).
3. Appuyez sur 9 9 1. La DEL rouge clignote deux fois.
4. Appuyez ensuite sur POWER.
5. Pointez la ONE FOR ALL vers votre téléviseur. Appuyez maintenant à
plusieurs reprises sur Chaîne +, jusqu’à ce que votre téléviseur s’éteigne (à
chaque appui sur la touche Chaîne +, la ONE FOR ALL envoie le signal
POWER du code suivant contenu dans la mémoire). Vous pouvez devoir
appuyer de nombreuses fois sur cette touche (jusqu’à 150 fois), soyez donc
patient.
6. Dès que votre téléviseur s’éteint, appuyez sur SETUP pour mémoriser le code.
Méthode de recherche
Programmation des codes
(
Exemple : configuration de la TÉLÉCOMMANDE ONE FOR ALL
pour la télévision)
F
RANÇAIS
F
RANÇAIS
1. Find the four-digit device code for your device (e.g. Accent television)
i
n the Code list. Codes are listed by device type and brand name. The most
popular code is listed first. If your brand is not listed at all please try the
C
ode Search. Make sure your equipment is switched on. If not switch it on
manually.
2. Press and hold down the SETUP key until the red LED underneath
t
he POWER key blinks twice (the red LED will blink once then twice).
3
. Enter your four-digit device code using the number keys (e.g. TV - Accent
code 0037). The red LED lights up twice.
4. Now, aim the ONE FOR ALL at your device and press POWER. If your
d
evice switches off, the ONE FOR ALL REMOTE is ready to operate your
device. If it does not switch off your device simply try the next code listed
f
or your brand.
If none of the codes listed for your brand work please try the Code Search.
The Code Search may also work if your brand is not listed at all.
EN Requires 2 new AAA Batteries
DE Benötigt 2 neue AAA Batterien
FR Fonctionne avec 2 piles AAA neuves
ES Requiere 2 pilas AAA nuevas
PT Requer 2 pilhas AAA novas
IT Richiede 2 nuove pile AAA
NL Vereist 2 nieuwe AAA-batterijen
DA Kræver 2 nye AAA batterier
NO Krever 2 nye AAA-batterier
SV Kräver 2 nya AAA-batterier
FI Vaatii 2 uutta AAA-paristoa
EL Λειτουργεί με 2 μπαταρίες ΑΑΑ νέα
RU Требуется 2 новые батарейки типа AAA
TR 2 yeni AAA Pil gerektirir
PL Wymaga 2 baterii AAA nowych
CZ Vyžaduje 2 nové AAA baterie
HU Szükség van 2 új AAA elem
SK Vyžaduje 2 nové AAA batérie
HR Zahtijeva 2 nove AAA baterije
RO Necesita 2 baterii AAA noi
BG Изисква 2 батерии тип AAA
The Search Method allows you to find the code for your device by scan-
ning through all the codes contained in the memory of the ONE FOR ALL.
The Search Method may also work if your brand is not listed at all.
1. Switch on your television (not on standby).
2. Press and hold down the SETUP key until the red LED underneath the
POWER key blinks twice (the red LED will blink once then twice).
3. Press 9 9 1. The red LED will blink twice.
4. Next, press POWER.
5. Aim the ONE FOR ALL at your Television. Now press CH+ over and over,
until your Television turns off (everytime you press the CH+ key the ONE
FOR ALL will send out a POWER signal from the next code contained in the
memory). You may have to press this key many times (up to 150 times) so
please be patient.
6. As soon as your television turns off, press the SETUP key to store the code.
Code Search
Code Set up
(Example: To set up the ONE FOR ALL REMOTE for your television)
6. Repeat steps 3 and 4 for each key you want to learn – remember you can
l
earn from multiple remotes, but only one function per key.
7
. When you learned all the functions you require, press and hold the SETUP
key until the red LED blinks twice.
If the red LED shows one long blink at step 5, the function was not learned
correctly, please try again from step 3.
If you find one or more keys don’t work properly after set up, you
can re-enter the learning mode at any time by repeating the procedure
f
rom step 1.
H
ow to delete a learned function to obtain the original function?
1
. Press and hold down the SETUP key until the red LED underneath
the POWER key blinks twice (the red LED will blink once then twice).
2. Press 9 7 6.
3. Press the key to be deleted (e.g. red key) twice.
5.
D
i
e
ro
t
e
L
E
D
b
l
i
nk
t
z
w
e
i
m
a
l
,
w
o
du
rc
h
a
ng
e
g
e
b
e
n
w
i
rd,
da
ss
di
e
T
a
st
e
o
rdnu
ng
sg
e
m
ä
ß
k
o
p
i
e
r
t
w
u
rde
.
6.
W
i
e
de
r
ho
l
e
n
S
i
e
di
e
S
c
hr
i
t
t
e
3
u
nd
4
f
ü
r
j
e
de
T
a
st
e
,
di
e
k
o
p
i
e
r
t
w
e
rde
n
so
l
l
.
D
e
nk
e
n
S
i
e
da
r
a
n,
da
ss
v
o
n
m
e
hre
re
n
Fe
r
nb
e
di
e
nu
ng
e
n
k
o
p
i
e
r
t
w
e
rde
n
k
a
nn,
a
b
e
r
nu
r
e
i
ne
F
u
nk
t
i
o
n
p
ro
T
a
st
e
.
7.
We
nn
S
i
e
a
l
l
e
b
e
t
i
g
t
e
n
F
u
nk
t
i
o
ne
n
k
o
p
i
e
r
t
ha
b
e
n,
ha
l
t
e
n
S
i
e
di
e
T
a
st
e
S
E
T
U
P
g
e
drü
c
k
t
,
b
i
s
di
e
ro
t
e
L
E
D
z
w
e
i
m
a
l
b
l
i
nk
t
.
We
nn
di
e
ro
t
e
L
E
D
b
e
i
S
c
hr
i
t
t
5
e
i
nm
a
l
l
a
ng
e
a
u
e
u
c
h
t
e
t
,
w
u
rde
di
e
F
u
nk
t
i
o
n
ni
c
h
t
r
i
c
h
t
i
g
k
o
p
i
e
r
t
.
Ve
rsu
c
he
n
S
i
e
e
s
v
o
n
S
c
hr
i
t
t
3
a
n
no
c
h
e
i
nm
a
l
.
We
nn
S
i
e
f
e
st
st
e
l
l
e
n,
da
ss
e
i
ne
o
de
r
m
e
hre
re
T
a
st
e
n
na
c
h
de
r
E
i
nr
i
c
h
t
u
ng
ni
c
h
t
r
i
c
h
t
i
g
f
u
nk
t
i
o
ni
e
re
n,
k
ö
nne
n
S
i
e
de
n
K
o
p
i
e
r
m
o
du
s
j
e
de
rz
e
i
t
e
r
ne
u
t
st
a
r
t
e
n,
i
nde
m
S
i
e
de
n
Vo
r
g
a
ng
v
o
n
S
c
hr
i
t
t
1
a
n
w
i
e
de
r
ho
l
e
n.
Wi
e
k
ö
n
n
e
n
S
i
e
d
i
e
ge
l
e
r
n
t
e
F
u
n
k
ti
o
n
l
ö
s
c
h
e
n
u
n
d
w
i
e
d
e
r
d
i
e
u
r
s
p
r
ü
n
gl
i
c
h
e
F
u
n
k
ti
o
n
a
u
s
f
ü
h
r
e
n
?
1.
D
ru
̈
c
k
e
n
u
nd
ha
l
t
e
n
S
i
e
di
e
T
a
st
e
S
E
T
U
P
g
e
dru
̈
c
k
t
,
b
i
s
di
e
ro
t
e
L
E
D
u
n
t
e
r
de
r
P
O
W
E
R
-T
a
st
e
z
w
e
i
m
a
l
b
l
i
nk
t
(
di
e
ro
t
e
L
E
D
b
l
i
nk
t
e
i
nm
a
l
,
da
nn
z
w
e
i
m
a
l
)
.
2.
D
c
k
e
n
S
i
e
9
7
6
.
3.
D
c
k
en S
i
e di
e
T
a
st
e z
u
m
L
ösc
hen z
w
ei
m
a
l
.
E
NGLISH
E
NGLISH
Instruction Manual
URC1210
Universal Remote Control
Contour TV Device
RDN 1010615
(Accent)
x2
x2
Acer
1
2
3
4
Accent
Acer
Accent
OFF
Acer
A
ccent
ON
Code List
4 Appuyez brièvement sur le bouton correspondant sur la télécommande
d
origine (le bouton d’alimentation, dans notre exemple).
5
. Le voyant rouge clignote deux fois afin d’indiquer que la copie a été
effectuée correctement.
6. Répétez les étapes 3 et 4 pour chacun des boutons à programmer. N’oubliez
p
as que vous pouvez copier des fonctions à partir de différentes télécomman-
des, mais qu’un bouton donné ne peut être associé qu’à une seule fonction.
7. Une fois toutes les fonctions de votre choix copiées, maintenez enfoncéle
b
outon SETUP jusqu’à ce que le voyant rouge clignote deux fois.
Si le voyant rouge német qu’un clignotement long lors de l’étape5, la fonction
n’a pas été correctement copiée. Reprenez la procédure à partir de l’étape 3.
Si l’un des boutons ne fonctionne pas correctement une fois
la configuration terminée, vous pouvez repasser en mode d’apprentissage
à tout moment en reprenant la procédure depuis l’étape 1.
P
our supprimer une fonction apprise et rétablir la fonction d'origine.
1
. Enfoncez et maintenez la touche SETUP jusqu’à ce que la DEL rouge sous la
touche POWER clignote deux fois (la DEL rouge clignote une fois puis deux
fois).
2
. Appuyez sur les touches 9 7 6.
3
. Appuyez deux fois sur la touche à supprimer (la touche rouge,
par exemple).
Your One For All remote control can learn any function from any other working
remote control. To do this, firstly make sure you have all your original remote
controls to hand, and that they have working batteries in. To learn functions,
the original remote should be approximately 3cm from the OFA remote, poin-
ting towards it as shown below:
1. Press and hold down the SETUP key until the red LED underneath the
POWER key blinks twice (the red LED will blink once then twice).
2. Press 9 7 5
3. Press and release the key you want to learn a function onto (for example
the TV Power key) – The red LED will blink continuously.
4. Press and release the corresponding key on the original remote,
for example Power.
5. The red LED will blink twice to indicate the key has been learned correctly.
Learning (copy)
Die One For All-Fernbedienung kann jede beliebige Funktion einer anderen
funktionierenden Fernbedienung kopieren. Stellen Sie dafür zunächst sicher,
dass Sie alle Ihre Originalfernbedienungen zur Hand haben und dass funktio-
nierende Batterien eingesetzt sind. Um Funktionen zu kopieren, muss die
Originalfernbedienung etwa 3 cm von der OFA-Fernbedienung entfernt sein
und wie unten dargestellt auf sie zeigen:
1. Drücken und halten Sie die Taste SETUP gedrückt, bis die rote LED unter
der POWER-Taste zweimal blinkt (die rote LED blinkt einmal, dann zweimal.
2.
Drücken Sie 9 7 5.
3. Drücken und lassen Sie die Taste los, für die eine Funktion kopiert werden
soll (z. B. die Ein/Aus-Taste für den Fernseher). Die rote LED blinkt dauerhaft
4. Drücken Sie die entsprechende Taste auf der Originalfernbedienung und
lassen Sie sie los, z. B. die Ein/Aus-Taste.
Kopieren
2
- 5 CM
GUIDE
Il est possible de copier nimporte quelle fonction d’une télécommande
opérationnelle sur votre télécommande One For All. Pour ce faire, assurez-vous
de disposer de toutes les télécommandes d’origine et que celles-ci sont en état
de fonctionnement. Pour que les fonctions puissent être copiées, la
télécommande d’origine doit se trouver à une distance d’environ 3 cm
de la télécommande OFA et être dirigée vers celle-ci (voir illustration ci-dessous).
1. Enfoncez et maintenez la touche SETUP jusqu’à ce que la DEL rouge sous la
touche POWER clignote deux fois (la DEL rouge clignote une fois puis deux fois).
2. Appuyez sur les touches 9 7 5.
3. Appuyez brièvement sur le bouton auquel vous souhaitez associer
la fonction à copier (par exemple, le bouton d’alimentation). Le voyant
rouge clignote alors de manière continue.
Apprentissage
2 - 5 CM
GUIDE
(3 sec.)
Contour TV _ URC1210 _ 75x250_Opmaak 1 31-03-16 17:08 Pagina 1
1


Need help? Post your question in this forum.

Forumrules
1

Forum

one-for-all-urc-1210

Reset search

  • The red power button on my remote has started flashing continuously Submitted on 12-4-2021 at 13:14

    Reply Report abuse
  • how do i access subtitles /mute and DVD on this remote Submitted on 31-7-2020 at 10:54

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for One for All URC 1210 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of One for All URC 1210 in the language / languages: All languages as an attachment in your email.

The manual is 6,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of One for All URC 1210

One for All URC 1210 Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info