Manual Omron M4-I - HEM-752-E (page 4 of 8) (English)

504923

Zoom out

Zoom in

1/8

English

➌ Fitting the cuff

Wrap the cuff around your bare left arm so that the

green colored band (indicating the centre of the blad-

der) is positioned 1 – 2 cm above your elbow joint on

the inside of your arm (see picture).

Important! If you push up your sleeve, ensure it does

not constrict the blood flow in your arm.

Close the cuff with the fabric fastener. The green area

of the cuff must cover the brachial artery.

The standard-sized cuff is designed for an arm

circumference of 22 – 32 cm. To ensure accurate

readings on arms with a circumference greater than

32 cm a large cuff will be required.

(large cuff code: CL)

Lay your arm on a table or support (e.g. a cushion)

with the palm of your hand facing upwards so that the

cuff is approximately at heart level. In this way you

ensure that the blood pressure measurement ob-

tained is neither artificially high (measurement below

heart level) nor low (measurement above heart level).

➍ Inflating the cuff

The OMRON M4-I is a blood pressure monitor with

an intelligent system to detect your personal blood

pressure.

Using the intelligence of the “Fuzzy Logic” this

device determines automatically the correct level

of inflation pressure. Just push the START button

().

The cuff must only be inflated when fitted to

your arm!

➎ The measurement starts

When the target inflation value is reached, the air is auto-

matically released. The value in the display counts down-

wards.

As soon as the monitor detects your pulse the ( ) sym-

bol begins to flash.

When the monitor no longer detects your pulse whilst the

cuff pressure is dropping, your systolic and diastolic blood

pressures (upper and lower values) will be displayed.

The deflation symbol ( ) will now flash to indicate the

end of the measurement.

When all the air has been released the ( ) symbol

appears on the display and your blood pressure and pulse

will be displayed on the screen for 5 minutes.

In some rare cases there are people where this measuring

method does not work due to physical structure. In such

cases OMRON recommends you to consult a doctor.

➏ Successive readings

Please leave an interval of at least 2 – 3 minutes should be

made in between two successive readings, otherwise the

blood flow of the arm could be constricted, which would

distort the results of the reading.

Switch off the device by pressing the ON/OFF ( ) button.

The device switches off automatically after approximately 5

minutes.

In order to obtain meaningful readings, you should mea-

sure your blood pressure regularly at the same time of day,

ideally every morning and evening.

➐ How to use the memory function

This monitor has a memory capable of storing fourteen sets

of readings. Every time you complete the measurement, the

monitor automatically stores blood pressure and pulse rate

values.

Push the ( ) button to recall stored readings while the

Heart Symbol ( ) is displayed.

Once the memory holds fourteen sets of readings, the

oldest set will be deleted to store a new set.

To delete stored readings, press the ( )button and the

Start Button together, then all the readings will be deleted.

NOTE: You can not delete stored readings partially.

START

1 - 2 cm

Right hand measurement

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Omron M4-I - HEM-752-E in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Omron M4-I - HEM-752-E Manual

Product: