694433

Olympia Fires Muria Manual

6
Zoom out
Zoom in
Previous page
1/9
Next page
Objects made of combustible materials mst not be placed onto the appliance or in a distance
smaller than the safety distance from the appliance.
4.2 Measures in the event of fire in the chimney
During normal operation, especially if damp fuel is used, soot and tar build up in the chimney. If
the chimney is not regularly checked and cleaned, danger of fire in the chimney will increase.
If this happens, proceed as follows:
do not, under any circumstances, extinguish with water
close all air inlets for combustion, if possible cover up the chimney
contact a chimney service to examine the chimney condition after the fire
contact the manufacturer to check the appliance
If combustible vapours or gases originate, there is a fire or explosion hazard; the stove must be
taken out of service (put out, remove ashes) and proper ventilation must be ensured.
5. First firing
Before and during the first firing leave the stove and ashpan doors slightly open (ca. 1-2 mm) so
that the sealing material does not amalgamate with the varnish. The varnish will harden as late as
after a few hours of firing. Check how the fireclay plates are settled in the combustion chamber
before making the first fire. Keep the temperature rather low during the first firing (feed the fire
more often with smaller amounts of fuel). All materials must adapt to heat development and the
hearth lining will dry slowly. The stove varnish will harden, which will be accompanied by
temporary odour; this odour will later entirely disappear. This provides that no microcracks,
varnish damage or material warping will occur. If the stove is lined with tiles, a fine microcrack
structure will appear on the tiles. This is not a defect; it is a natural accompaniment of heat stress
of the glaze. Sounds ocuring during the heating up or cooling of the stove do not signalize any
defect either.
During the hardening of varnish, sufficient room ventilation must be ensured and pets or birds
must not stay in the room where varnish vapours are present.
5.1 Fire lighting
Insert some crumpled paper into the combustion chamber and put small pieces of wood on it.
Lighting the fire is very easy with a solid firelighter. After lighting, leave the fire to flare up freely
with both the primary and the secondary inlets open. It is prohibited to use flammable liquids (such
as benzine, paraffin oil, etc.) for lighting the fire. As soon as the fire starts to burn and the draught
is sufficient, bigger logs or briquettes can be inserted without fear of excessive smoke. The
combustion air will enter to the fuel from below through the grate. Insert maximum the given
amount of fuel depending on the rated stove output. Fuel consumption is given in the respective
technical data tables. Burning intensity can be regulated by means of the primary air control
elements or by reducing the chimney draught, if there is a smoke flap installed. Bigger amounts of
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olympia Fires Muria at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olympia Fires Muria in the language / languages: English as an attachment in your email.

The manual is 0,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info