Manual OK ODW 122 (page 17 of 138) (English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish)

783022

Zoom out

Zoom in

1/138

17 EN

INSTALLATION

Note: The dishwasher is equipped with power cord and plug. Make sure before installation that the wall

outlet is at the desired place of installation.

Consider the dimension of the product for placing and installation.

1 Place the dishwasher on an even, horizontal and steady surface, e.g. place it on a suitable desk in

your kitchen.

Note: The dishwasher is not intended to be built in.

2 The dishwasher must be connected to drainage.

1. The hose is already connected the waste water outlet. Cut the straps and unwind the hose.

2. Connect the end to a drainpipe. Observe the max. height of the outlet of drainage hose.

Note:

A suitable hose holder is available as optional accessories.

3 Connect the water inlet to tap water supply (3/4”) using the provided hose and make sure it

fastened tightly.

Note: If the water pipes are new or have not been used for an extended period of time, let the

water run to make sure that the water is clear and free of impurities. If this precaution is not taken,

there is a risk that the water inlet can get blocked and damage the appliance.

4 Connect the power plug to the mains.

Note: Before using the product for the rst time, make sure that all hydrophilic connections of the

product are correctly sealed and connected to both the device as well as the water mains. Check all

connections periodically to avoid possible leakage.

PREPARATION

5 Putting salt into the salt container

Depending on your tap water hardness (hardness degree) use additional salt (water softener).

Always consider instruction provided with the salt.

1. Remove the basket and then unscrew and remove the cap from the salt container.

2. Before rst wash, add 1 lt. of water in the salt container of your machine.

3. Place the end of the funnel (supplied) into the hole and introduce about 1 kg of salt. It is normal

for a small amount of water to come out of the salt container.

4. After lling the container, screw the cap tightly back clockwise.

5. Immediately after lling the salt into the salt container, a washing program should be started

(rapid program suggested). Otherwise lter system, pump or other important parts of the

machine may be damaged by salty water which is out of warranty.

Note: Usually, the salt warning light will be cease to be illuminated within 2-6 days after the salt

container has been lled with salt. Depending on how fully the salt dissolves, the salt warning light

may still be on even though the salt container is lled.

Warning!

• Only use salt specically designed for use in dishwashers! All other types of salt not specically

designed for use in a dishwasher, especially table salt, will damage the water softener. In case of

damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is

liable for any caused damages.

• If there are spills of the salt, a soak or a rapid program should be run to remove the excess salt.

• Only ll with salt just before starting one of the complete washing programs. This will prevent any

grains of salt or salty water, which may have been split, remaining of the bottom of the machine for

any period of time, which may cause corrosion.

• The salt container must only be relled when the salt warning light in the control panel comes on.

IM_ODW121_ODW122_190719_V10_HR.indb 17 19/7/2019 10:05

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of OK ODW 122 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 15.58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

OK ODW 122 Manual

Product: