Manual Numark M6 USB (page 6 of 24) (English, German, French, Italian, Spanish)

618166

Zoom out

Zoom in

1/24

USB OPERATION

The M6 USB is equipped with a USB port which allows you to play content from your computer through the

mixer, or record audio from the mixer directly into your favorite software application. The USB interface on

your mixer works with your computer just like a standard USB sound card. In addition, the USB interface is

class-compliant, so there are no special drivers or software to install; simply connect a USB cable from the

USB port to your computer and you are ready to go!

AUDIO SETUP

The M6 USB is a class-compliant device that can be used with

any digital audio workstation or recording software that

supports USB audio. To enable your M6 USB to send and

receive audio to and from your computer, follow the

instructions below for your computer's operating system:

WINDOWS 7:

1. Use the included cable to connect the M6 USB to your

computer.

2. Go to Start Menu  Control Panel  Hardware and

Sound  Sound.

3. Click the Playback tab and select USB Audio Codec*

as the default device.

4. Click the Recording tab and select USB Audio Codec*

as the default device.

5. Click Properties in the lower right-hand corner.

6. In the new window, click the Advanced tab and select 2-

channel, 16-bit, 44100 Hz (CD Quality) as the default

format.

7. Uncheck both boxes under Exclusive Mode.

8. Click the Levels tab and set the slider to "4."

9. Click OK to close the Properties window.

10. Click OK to close the Sound control panel.

WINDOWS VISTA:

1. Use the included cable to connect the M6 USB to your

computer.

2. Go to Start Menu  Control Panel  Sound. (If you don't see Sound, select Switch to Classic

View, and the Sound Control Panel should become available.)

3. Click the Playback tab and select USB Audio Codec* as the default device.

4. Click the Recording tab and select USB Audio Codec* as the default device.

5. Click Properties in the lower right-hand corner.

6. In the new window, click the Advanced tab and select 2-channel, 16-bit, 44100 Hz (CD Quality) as

the default format.

7. Uncheck both boxes under Exclusive Mode.

8. Click OK to close the Properties window.

9. Click OK to close the Sound control panel.

WINDOWS XP:

1. Use the included cable to connect the M6 USB to your computer.

2. Go to Start Menu  Control Panel  Sounds and Audio Devices.

3. Click the Audio tab.

4. Under Sound Playback and Sound Recording, select USB Audio Codec* as the default device.

5. Click OK.

MAC:

1. Use the included cable to connect the M6 USB to your computer.

2. Go to Applications  Utilities  Audio MIDI Setup.

3. In the Audio Devices tab under System Settings, select USB Audio Codec* as your Default Input

and Default Output.

4. Close the window.

Be sure your audio software program is

set up to receive audio via the M6 USB.

This can usually be done in your

software's "Preferences" or "Device

Setup." Please consult your software

manual for more information.

* If you have other USB audio devices

connected to your computer, which may

have identical names, you may need to

try selecting each one until the M6 USB

is recognized.

If you experience too much latency

after adjusting your software latency

settings, we recommend the free

ASIO4ALL (Audio Stream Input/Output)

driver for PC at www.asio4all.com

ASIO drivers generally perform better

and with lower latency since they create

a more efficient communication

between audio devices and software.

WHAT CONNECTION LEAD DO YOU NEED TO CONNECT TO ONKYO AMPLIFIER Submitted on 10-12-2021 at 13:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Numark M6 USB in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Numark M6 USB Manual

Product: