618167

Numark M101 Manual

4
Zoom out
Zoom in
Previous page
1/16
Next page
4
REAR PANEL FEATURES
1. POWER SWITCH – Turns the mixer on and off.
Turn on the mixer after all input devices have been
connected and before you turn on amplifiers. Turn
off amplifiers before you turn off the mixer.
2. AC IN – Use the included power adapter to
connect the mixer to a power outlet. While the
power is switched off, plug the power supply into
the mixer first, then plug the power supply into a
power outlet.
Note: The mixer is designed to work with the
included power supply only. Using an incompatible
power supply could result in damage to the unit.
3. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this output to a speaker or amplifier system. The
level of this output is controlled by the MASTER knob on the top panel.
4. LINE INPUTS (RCA) – Connect line-level devices, such as CD players, samplers or audio interfaces, to these inputs.
5. PHONO INPUTS (RCA) – Connect phono-level devices, such as turntables, to these inputs.
6. GROUNDING TERMINAL – If you are using phono-level turntables with a grounding wire, connect the grounding wire to
these terminals. If you experience a low “hum” or “buzz”, this could mean that your turntables are not grounded.
Note: Some turntables have a grounding wire built into the RCA connection and, therefore, nothing needs to be
connected to the grounding terminal.
TOP PANEL FEATURES
1. POWER LED – Illuminates when the mixer is on.
2. STEREO LEVEL INDICATOR – Displays the audio
level of the Program mix.
3. MASTER – This control adjusts the output volume of the
Program mix.
4. MIC GAIN – Adjusts the audio level of the microphone
signal.
5. MIC TREBLE – Adjusts the high (treble) frequencies of
the microphone channel.
Tip: If you experience feedback when using a
microphone at loud levels, try turning down the high
frequencies.
6. MIC BASS – Adjusts the low (bass) frequencies of the
microphone channel.
7. CUE GAIN – Adjusts the level of the headphone audio.
8. CUE MIX – Turn to mix between Channels 1 and 2 in
the headphones. When all the way to the left, only
Channel 1 will be heard. When all the way right, only
Channel 2 will be heard.
9. CHANNEL GAIN – Adjusts the corresponding channel’s
pre-fader and pre-EQ gain level.
10. CHANNEL TREBLE – Adjusts the high (treble)
frequencies of the audio on the corresponding channel.
11. CHANNEL BASS – Adjusts the low (bass) frequencies
of the audio on the corresponding channel.
12. INPUT SELECTOR – Selects the input source to be routed to the corresponding channel. Input jacks are located on the
rear panel.
13. CHANNEL FADER – Adjusts the audio level on the corresponding channel.
14. CROSSFADER – Blends audio playing between Channels 1 and 2. Sliding this to the left plays channel 1 and sliding to
the right plays Channel 2.
Note: The crossfader is user-replaceable if it should ever wear out. Simply remove the facepanel, then remove the
screws holding it in position. Replace the fader with a quality authorized replacement from your local Numark retailer
only.
15. MIC INPUT – Connect ¼” microphones to this input. The microphone controls are located on the top panel.
16. HEADPHONES – Connect your ¼” headphones to this output for cueing and mix monitoring.
1
6
2
3
3
4
4
4
4
5
5
5
5
1
2
14
15 16
3
49
10
11
12 12
13
13
10
11
9
5
6
7
8
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Numark M101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Numark M101 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info