24743

Numark CM200 Manual

3
Zoom out
Zoom in
Previous page
1/17
Next page
3
MIXER QUICK SETUP
1. Make sure all items listed on the
front of this guide are included
in the box.
2. READ SAFETY INSTRUCTION
BOOKLET BEFORE USING THE
PRODUCT.
3. Study this setup diagram.
4. Place mixer in an appropriate
position for operation.
5. Make sure all devices are turned
off and all faders and gain knobs
are set to “zero”
6. Connect all stereo input sources
as indicated in the diagram.
7. Connect the stereo outputs to
power amplifier(s), tape decks,
and/or other audio sources.
8. Plug all devices into AC power.
9. Switch everything on in the
following order.
• audio input sources (i.e.
turntables or CD players)
• mixer
• last, any amplifiers or
output devices
10. When turning off, always
reverse this operation by,
• turning off amplifiers
• mixer
• last, any input devices
11. Go to http://www.numark.com
for product registration.
More information about this
product may be found at
http://www.numark.com
REAR CONNECTIONS
1. Phono Inputs: This input is used for connecting
your turntables through the sensitive RIAA phono
preamplifiers. Only turntables with phono level
output should be attached. Line level turntables
must be attached to the line inputs.
2. GND: This screw connector should be used to
secure any turntables or other devices connected
to the mixer that need to be grounded.
3. Line Inputs: CD players, Tape Decks, Samplers
or other line level input devices should be
connected to these inputs.
4. Microphone Input: Microphones with a ¼”
connector can be connected to these input
terminals.
5. Fader Start Connector: to attach your mixer to
a remote start equipped Numark CD player using
industry standard 1/8”(3.5mm) cables.
6. Record Output: This RCA output is for
connecting a recording device such as a tape
deck or CD recorder. The level of the record
output is based upon pre-master levels.
7. Zone Output (RCA): This output is for
connecting an external monitoring device such as
a PA system, powered monitors or a home
stereo. The level of the zone stereo output signal
is controlled by the zone fader.
8. Master Output (RCA): This output is for
connecting an external monitoring device such as
a PA system, powered monitors or a home
stereo. The level of the master stereo output
signal is controlled by the master fader.
9. Stereo Balanced Master Outputs (XLR): low-
impedance XLR type connectors controlled by the
Master fader.
10. AC In: This mixer is designed to work with the
power supply cord that comes with the unit.
While the power is switched off, plug the power
supply into the mixer first, then plug it into the
outlet.
11. Voltage Selector: Set this to the correct voltage
for your location standard.
12. Power Switch: Use this switch to turn on the
mixer after all input devices are already
connected to prevent damage to your equipment.
Turn the mixer on before you turn on amplifiers
and turn of amplifiers before you turn off the
mixer.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Numark CM200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Numark CM200 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info