23412

Numark 200FX Manual

3
Zoom out
Zoom in
Previous page
1/22
Next page
MIXER QUICK SETUP
1. Make sure all items listed on the front of
this guide are included in the box.
2. READ SAFETY INSTRUCTION BOOKLET
BEFORE USING THE PRODUCT.
3. Study this setup diagram.
4. Place mixer in an appropriate position for
operation.
5. Make sure all devices are turned off and all
faders and gain knobs are set to “zero”
6. Connect all stereo input sources as
indicated in the diagram.
7. Connect the stereo outputs to power
amplifier(s), tape decks, and/or other audio
sources.
8. Plug all devices into AC power.
9. Switch everything on in the following order.
• audio input sources (i.e. turntables or
CD players)
• mixer
• last, any amplifiers or output devices
10. When turning off, always reverse this
operation by,
• turning off amplifiers
• mixer
• last, any input devices
11. Go to http://www.numark.com for product
registration.
More information about this product may be
found at http://www.numark.com
1
222
3131333
44
44
5
67899
10
11
12
REAR CONNECTIONS
1. Phono Inputs: This input is used for
connecting your turntables through the
sensitive RIAA phono preamplifiers. Only
turntables with phono level output should be
attached. Line level turntables must be
attached to the line inputs.
2. GND: This screw connector should be used
to secure any turntables or other devices
connected to the mixer that need to be
grounded.
3. Line Inputs: CD players, Tape Decks,
Samplers or other line level input devices
should be connected to these inputs.
4. Microphone Input: Microphones with a ¼”
connector can be connected to these input
terminals.
5. Fader Start Connector: to attach your
mixer to a remote start equipped Numark CD
player using industry standard 1/8”(3.5mm)
cables.
6. Zone Output (RCA): This output is for
connecting an external monitoring device
such as a PA system, powered monitors or a
home stereo. The level of the zone stereo
output signal is controlled by the zone fader.
7. Record Output: This RCA output is for
connecting a recording device such as a tape
deck or CD recorder. The level of the record
output is based upon pre-master levels.
8. Master Output (RCA): This output is for
connecting an external monitoring device
such as a PA system, powered monitors or a
home stereo. The level fo the master stereo
out put signal is controlled by the master
fader.
9. Stereo Balanced Master Outputs (XLR):
low-impedance XLR type connectors
controlled by the Master fader.
10. AC In: This mixer is designed to work with
the power supply cord that comes with the
unit. While the power is switched off, plug
the power supply into the mixer first, then
plug it into the outlet.
11. Voltage Selector: Set this to the correct
voltage for your location standard.
12. Power Switch: Use this switch to turn on
the mixer after all input devices are already
connected to prevent damage to your
equipment. Turn the mixer on before you
turn on amplifiers and turn of amplifiers
before you turn off the mixer.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Numark 200FX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Numark 200FX in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info