534379
14
Zoom out
Zoom in
Previous page
1/16
Next page
EN 14
firm click. The ceiling unit will now remain suspended in place.
5
Drehen Sie die vier Klemmschrauben von Hand fest, um die Deckeneinheit endgültig zu befestigen. Achtung: drü-
cken Sie dabei die Dunsthaube nicht nach oben und ziehen Sie die Halteklammern nicht zu stark an, da sie sich sonst
unnötig verbiegen. Sobald diese Klemmschrauben festgedreht sind, ist die Deckeneinheit einsatzbereit.
Connecting external lighting
6
It is possible to switch external lighting (max. 300W) via the remote control of the cooker hood.
A Connect the power cable of the lighting to the connector (864027) included in the delivery.
B Next, connect this connector, which is located on the back of the cooker hood.
Removing the ceiling unit
7
Before dismounting, protect the cooking plate, for example using cardboard or cloth, in case a screw or clamp is
dropped onto it. To remove the ceiling unit, the 4 clamping screws have to be fully loosened. When these are loose,
the ceiling unit can be taken down. Watch out: the loosened clamping springs may drop down.
Remote installation of the motor unit
8
Take the motor unit from the ceiling unit by removing the 8 mounting screws (see (2)); use these screws again to
mount the tube adapter to the ceiling unit. You can loosen the plugs on the motor unit.
9
These are the possibilities of the positions the motor unit may occupy.
10
A Determine the location and the suspension position of the motor unit. If necessary, the exhaust direction of the
motor can be changed. The supply and exhaust pipes can be made in a 90° angle or opposite each other. TAKE
CARE: make sure the motor shaft is horizontal at all times!
B Screw the tube adapter (6830029) to the bottom of the motor using the screws (8x906151).
11
Mount the suspension bracket to the motor housing. This is done by first unscrewing the screws provided from the
motor housing. After this, place the suspension bracket onto the motor unit and screw it back on using the same
screws. You can choose position A or position B.
12
To mount the motor unit onto the wall, you first mark out the 4 drilling holes.
13
To mount onto a stone wall: use the screws 906055 and the plugs 906143.
- Drill the 4 marked-out points and place the plugs into the holes.
- Partly screw in 2 screws in position 1 and position 2.
- Suspend the motor unit over these 2 screws. Next, tighten the screws.
- Now screw in the screws in position 3 and position 4.
To mount onto a wooden wall: use the screws 906192.
- Partly screw in 2 screws in position 1 and position 2.
- Suspend the motor unit over these 2 screws. Next, tighten the screws.
- Now screw in the screws in position 3 and position 4.
14
Connect the plastic exhaust (864006) onto the tube adapter using 4 screws (906151).
15
Mount the suction and exhaust pipe to the motor unit by means of a hose clamp. Connect the plug of the cable co-
ming from the ceiling unit to the plug on the motor unit.
INSTALL THE EXHAUST DUCT
The exhaust of the hood must be properly taken care of. For optimum performance of the hood it is important to pay
attention to the following items during the installation:
Use smooth, non-flammable pipes with an internal diameter that is equal to the external diameter of the connection
nozzle of the hood. Maximally extend flexible ducts and cut them to size.
Do not reduce the exhaust diameter. This will lower the capacity and raise the noise level.
Make the duct as short as possible and with as few as possible bends to the outside.
Avoid square bends. Use rounded bends for proper air conduction.
Flat duct: the surface of a flat duct must be the same size as Ø150 mm = 177 cm².
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novy D6843 Pureline at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novy D6843 Pureline in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Novy D6843 Pureline

Novy D6843 Pureline User Manual - English, German, Dutch, French - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info