741630
19
Zoom out
Zoom in
Previous page
1/20
Next page
19
NL
40
Schuif beide bovenste opvangbakjes n° 1821107
in de afzuigkap.
41
Plaats beide vetfilters in de afzuigkap op de val-
beveiliging.
42
Verifieer de juiste plaatsing van de vetfilters aan
de hand van het positioneerlipje.
43
Plaats het voorste glas op de toren van de af-
zuigkap.
Positioneer
de lipjes van het glas in de uitspar-
ing van de toren en kantel het glas naar de mag-
neten toe tot het glas aantrekt.
44
Druk op de knop om de toren terug te her-
initialiseren.
45
De toren beweegt nu naar de gesloten positie.
46
Recirculatie: Toestel staat standaard ingesteld
in recirculatiemodus
Afvoer
: zet toestel in afvoermodus door de toe-
tsencombinatie “+” en “-” en
gedurende 3
seconden in te drukken. De led naast
knip-
pert 3x om de instelling te bevestigen.
Herhaal bovenstaande pr
ocedure om terug naar
recirculatiemodus over te schakelen. De led is nu
3 seconden aan.
47
OPTIONEEL: Installatie I/O module n° 990036
V
erwijder het afdekplaatje van de aansluitcon-
nector.
48
Sluit de I/O module connectie kabel aan op de
aansluitconnector. (Zie handleiding 990036 I/O
module)
FR
40
Glissez les deux bacs de collecte supérieurs n°
1821107 dans la hotte.
41
Placez les deux filtres à graisse dans la hotte, sur
la sécurisation antichute.
42
Vérifiez si les filtres à graisse sont positionnés
correctement à l’aide de la languette de posi-
tionnement.
43
Placez le verre avant sur la tour de la hotte.
Positionnez les languettes du verr
e dans l’évide-
ment de la tour et basculez le verre vers l’aimant
jusqu’à ce que le verre soit attiré.
44
Actionnez le bouton pour réinitialiser la tour.
45
La tour se déplace maintenant vers la position
fermée.
46
Mode recyclage : La hotte est par défaut en
mode recyclage.
Mode évacuation : appuyez simultanément
pendant 3 secondes sur les touches “+” et “-”
et
. La led à côté de clignote 3 fois pour
confirmer le réglage.
Répétez ces actions pour le mode de reicrula-
tion, le led sera allumé pendant 3 secondes.
47
OPTION: Installation Module I/o n° 990036 Reti-
rez le couvercle du connecteur de connexion.
48
Branchez le câble de connexion du module d’
I/O dans le connecteur. (Voir 990036 guide Mo-
dule I/O)
DU
40
Schieben Sie die beiden oberen Auffangbehälter
n° 1821107 in den Dunstabzug.
41
Platzieren Sie die beiden Fettfilter im Dunstabzug
auf dem Fallschutz.
42
Überprüfen Sie die korrekte Positionierung der
Fettfilter mithilfe der Positionierlasche.
43
Platzieren Sie die vordere Glasplatte auf dem
Lüftungsschirm des Dunstabzugs.
Positionier
en Sie die Laschen der Glasplatte in
der Aussparung des Lüftungsschirms und kip-
pen Sie die Glasplatte auf die Magnete zu, bis
die Magnete die Glasplatte anziehen.
44
Drücken Sie die Taste , um den Lüftungs-
schirm neu zu initialisieren.
45
Der Lüftungsschirm bewegt sich jetzt in die ge-
schlossene Position.
46
Umluft: Das Gerät ist standardmäßig für Umluft-
betrieb programmiert.
Abluft:
Sie können das Gerät durch Drücken der
Tastenkombination “+” und “-” und
für ca. 3
Sekunden, in den Abluftmodus umstellen.
Die nebenstehende LED blinkt dr
eimal, um
die Einstellung zu bestätigen. Wiederholen Sie
diese Schritte, gelangen Sie wieder in den Um-
luftmodus. In diesem Fall leuchtet die LED für 3
Sekunden, um den Moduswechsel zu bestäti-
gen.
47
OPTIONAL: Installation eines I/O-Schalter-
Moduls (Fensterkontakt) Nr. 990036. Entfernen
Sie die Abdeckung vom Steckeranschluss.
48
Stecken Sie die Verbindung des I/O Schalter-
Moduls in den Anschluss. (Siehe Handbuch
990036 I/O-Schalter-Modul)
EN
40
Slide both upper collection trays n° 1821107
into the hood.
41
Place both grease filters in the hood on the fall
protection.
42
Verify the correct placement of the grease filters
using the positioning tab.
43
Place the front glass on the hood tower.
Position
the tabs of the glass in the cut-out in
the tower and tilt the glass toward the magnets
until the glass snaps into place.
44
Press the knob to re-initialise the tower.
45
The tower now moves to the closed position.
46
Recirculation: Device is set in recirculation
mode by default.
Duct out: set device in duct out mode by press-
ing the key combination “+” and “-” and
dur-
ing 3 seconds. The led next to
will blink 3x to
acknowledge the setting.
Repeat these actions for recirculation mode, the
led will be on for 3 seconds.
47
OPTIONAL: Installation I/O module n° 990036
Remove the cover from the connection connec-
tor.
48
Plug in the I/O module connection cable into the
connector. (See manual 990036 I/O module)
18x1_110131_MA1.indd 1918x1_110131_MA1.indd 19 18/08/20 21:3118/08/20 21:31
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novy 1821 Novy Panorama Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novy 1821 Novy Panorama Pro in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Novy 1821 Novy Panorama Pro

Novy 1821 Novy Panorama Pro User Manual - English, German, Dutch, French - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info