665704

Novotecnica CS 61 Manual

7
Zoom out
Zoom in
Previous page
1/10
Next page
12
DITEC S.P.A - IP1580 30/06/99 - CS61/CS61E
1. TECHNICAL DATA
Power supply 230 V~ 50 Hz
Absorption 2 A
Motor power 250 W
Torque 700 N
Max. run 13 m
Max. door weight 600 kg
Speed 0.18 m/s
Intermittence S2 = 15 min. / S3 = 25%
Temperature -15 °C / +50 °C
Degree of protection IP54
Weight 12.7 kg
2. REFERENCE TO ILLUSTRATIONS
2.1 Standard installation references (fig. 1)
ATTENTION: Only use DITEC’s safety devices and accessories for installation.
1 Radio
2 Flashing light
3 Key selector
4 Connect power supply to an omni-pole switch with a contact opening gap of no less that 3 mm (not supplied
by us)
2.2 Geared motor references (fig. 2)
9 Geared motor
10 Carter
11 Release access door
12 Release
3. INSTALLATION
3.1 Preliminary checks
Check for gate stability and that the slide wheels are in good condition and the top guides do not cause any
friction. The slideway must be securely anchored to the ground and fully exposed along its full length. It must be
perfectly smooth so as to avoid jamming of the gate.
Provide an opening and closing stop.
Make sure that the gate is securely inserted in the slideway so that it cannot come out of the
slideway and fall.
Geared motor installation
Unless otherwise specified, all measurements are expressed in millimetres.
3.2 (Fig. 4) Lay a concrete foundation with buried anchoring brackets and the base plate, making sure that it is
pefectly level and smooth. Allow for 80 mm between the plate axis and the rack B . Route the cable ducts
through the two holes in the middle of the plate.
3.3 (Fig. 5) Open the release access door 11 , loosen the screw that locks the carter and lift it. Insert the
ancoring feet G at the gear motor base. Position the geared motor on to the base plate. Adjusting
gearmotor: horizontally by sliding in the ancoring feet notches, vertically with the 4 levelling screws D :
while adjusting vertically, keep the motor slightly raised above the base plate so as to allow enough
space to secure the rack and to make any subsequent adjustments, if necessary.
3.4 (Fig. 6) Secure the rack by disengaging the geared motor and opening the gate. Place the rack on pinion
15 and move the gate manually to secure the rack along its full length. Once the rack has been secured,
vertically adjust the geared motor so as to have a gap of 2 to 3 mm between the pinion and the rack. Finally,
firmly secure the geared motor by fitting shims E and washers F .
3.5 (Fig. 7, 8) Adjusting limit switch: secure the limit stop skids H on to the rack so that the gate stops about
20 mm before reaching the stop.
ENGLISH
5 Geared motor + Electrical board
6 Photocells
7 Rubber hip / Sensitive hip
8 Opening and closing stop
13 Electrical board
14 Limit-switch spring
15 Pinion
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novotecnica CS 61 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novotecnica CS 61 in the language / languages: English as an attachment in your email.

The manual is 0,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info