709179
3
Zoom out
Zoom in
Previous page
1/4
Next page
3
Photocell User Manual P5102
I. Technical Specification
1. Working voltage: 12~24VAC/DC
2. Working current (24VDC): emitter: 15mA receiver: 30mA
3. Photocell wavelength: 940nm
4. Angle of opposite emission: ± 5º
5. Receiver range: 12m
6. Internal rotation system adjusted angle: 0180 º
7. Working temperature: -20º +60
8. Relay contact loading capacity: 1A/30VDC
9. Waterproof grade: IP54
10. Size: 127x50x28mm
II. Safety Instruction
1. For security, please read the user manual carefully before initial operation;
2. Please be sure the power is off before connecting, the product is produced without fuse;
3. It is used only for the manual remote control and wireless control equipment / system, this system must not
endanger life or property during the running failure or its security risks have been eliminated;
4. Please operate the product in effective receive range.
III. Picture Display
IV. Installation Instruction
1. The product should be installed more than 20cm upper the ground (to avoid reflection), and the distance between
emitter and receiver shall be more than 0.5 meters (if not, maybe the photocell will be working on or cannot work);
2. the end user should install the photocell on the back of the direct sunshine or other strong shining (± 5º) to keep the
photocell work well steadily
3. Please try to avoid installing other photocell emitters within effective receive range;
4. If you should install many photocells on the same line, you can install receivers on two ends and then emitters in the
middle back to back which can effectively avoid the above-mentioned problem.
5. In order to avoid signal bias of emitters and receivers, which will easily cause misoperation, please install the
photocell firmly.
6. Connecting power after checking no error of connecting lines:
emitter LED lights, receiver LED lights, receiver NO/COM connects while NC/COM disconnects;
Making the CAP of emitter and receiver align, receiver LED off, NC/COM connects while NO/COM disconnects. If
the signal between emitter and receiver is interrupted, receiver LED lights, NC/COM disconnects while NO/COM
connects.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Novoferm P5102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm P5102 in the language / languages: English, German as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info