Manual Novoferm K3 VivoPort (page 5 of 24) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

709166

Zoom out

Zoom in

1/24

• The mains variant requires a 24V light bulb; the accumulator variant requires a 12V

light bulb.

• The light switches off approx. 1.5 minutes after the last run command.

• The operator runs for a maximum of approx. 40 seconds. If the door has not ope-

ned within this time the operator switches off.

• The sensitivity for switching off changes in the proximity of the expected “end

point”. In this area the force limit reacts more sensitively.

• For a mains or accumulator failure all data remains stored: logged on transmitters,

“open” reference time, “close” reference time and the last position of the door

(opened or closed)

• When the operator is connected to the power supply, the internal memory is first

checked. The checking lasts about 4 seconds – during this time running is not

possible.

Summary of the report messages by means of signal tones:

• 2 x beep after connecting the power supply: fault of the push button

- Cause: pushbutton on the device is permanently pressed. The pushbutton is

possibly jammed in the housing. (Beep repeats itself in this case approx. every

3 seconds)

• 2 x beep during a run command: motor standstill detected

- Cause: motor is blocked or faulty.

• 4 x beep during a run command: a run is not possible

- Cause: pass-door contact is open or opto-sensor of the force rocker switch is

obstructed or is dirty.

• 6 x beep during a run command: a run is not possible

- Cause: controller programme memory is faulty. Inform customer service ab-

out this.

• 3 x beep during a run command: undervoltage detected (only for accumulator

operation), a run is not possible

- Cause: accumulator voltage has sunk below a critical level. A run cannot be

started. Afterwards a regular signal tone is sounded for 60 seconds.

• 3 x beep during a run: undervoltage detected (only for accumulator operation),

operator stops

- Cause: accumulator voltage has sunk below a critical level during a run. A run

cannot be finished. After this the operator remains blocked for approx. 10 se-

conds and cannot be actuated.

• 5 x beep during a run command: temperature protection active

- Cause: the temperature of the MOS-FET transistor on the printed circuit bo-

ard has exceeded 75°C. Allow operator 20min. to cool down, start again.

• Regular signal tone after a run or permanently: accumulator voltage too low

- Cause: the accumulator capacity soon exhausted. Recharging is necessary.

Operating Instructions

The manufacturer’s liability expires with improper operation, maintenance

and/or if no original spare parts are used.

• Pull out the mains plug before starting any work whatsoever with the opera-

tor.

• Brief all persons that use the door system about safe operation in accor-

dance with regulations.

• In activating the operator all opening and closing actions must be supervi-

sed to ensure that neither persons nor objects are in the moving area of the

door.

• Hand-held transmitters and other remote control transmitters do not belong

in children’s hands

Functional sequence

• The garage door operator can be actuated by pressing the pushbutton on the

operator head or by other pulse generators such as hand-held transmitters, key

switches etc. Only a short pulse input is necessary.

• First pulse input

- operator starts and drives the door to the set end position OPEN or CLOSED

• Pulse input during the run

- door stops

• New pulse

- door continues the run in the opposite direction

Internal safety device

If the door runs into an obstacle during the run, the operator stops and the door can

be moved manually.

Pass-door contact (external safety device)

If there is a pass-door a pass-door contact (normally clo-

sed contact, a requirement in accordance with EN 12453)

must be fitted. For this the operator housing must be

opened and the small link next to the pass-door terminal

on the printed circuit board broken out with a screwdriver.

If the operator is activated when the pass-door is open

the run will not be made and the operator reports this by

emitting a beep tone four times.

If the link has been broken out and the pass-door contact

is no longer required, a link must be fitted in the terminal.

Emergency unlocking/ fast unlocking

During setting work, mains failure or disturbances the door can be unlocked by tur-

ning the inside handle and then operated by hand.

Orientation light

• The orientation light switches itself on after a pulse input and off again after 90s

• Change of light bulb: unscrew housing:

- mains variant: light bulb 24V, 5W, Ba9S

- accumulator variant: light bulb 12V, 4W, Ba9S

Hand-held transmitter

• Programming other hand-held transmitters (max. 4):

- see point 12

• Battery change

- Slide the battery compartment lid off the hand-held transmitter

- Fit the new battery (alkaline 23A, 12V). Pay attention to the correct polarity.

- Slide the battery compartment lid onto the hand-held transmitter

Maintenance/Checking

- Maintenance by qualified fitters -

For your safety you should get the door system checked by an expert company

before first putting into operation and then as required at least once a year.

• Checking the force limit

- Drive the door to the OPEN end position

- Position obstacles (e.g. cartons) under the door closing edge

- Start the door from the OPEN end position

- The operator drives to the obstacle and stops

The force on the main closing edge may not exceed the values demanded according

to DIN EN 12453. Depending on the use of the door, and because of national regula-

tions, more extensive precautionary measures may be necessary.

Attention! a strong closing force can lead to injuries to persons and/or damage

to property. Setting the force: see Programming Instructions

2 year manufacturer’s guarantee

Besides the guarantee based on our Terms of Sale and Delivery, we give a 2 year ma-

nufacturer’s guarantee for a maximum of 15,000 duty cycles on the operator systems

mentioned above (accumulators: see note concerning accumulator operation).

Should these, or any part thereof, prove unusable due to material or production faults,

or should such faults seriously impair their use, we will, at our discretion, repair it or

replace it.

For damages caused by improper installation and mounting, incorrectly putting into

operation, operation and maintenance not according to instructions, improper use

and any unauthorized changes to the operator and the accesory parts, no liability will

be accepted. The same applies to damages caused by transport, force majeure, ex-

ternal influences or natural wear and tear as well as by unusual atmosphere conditi-

ons.

After unauthorized changes or repairs to functional parts, or after application of addi-

tional filling weight that the specified multiple spring assemblies can no longer coun-

terbalance, no guarantee can be accepted.

Faults are to be reported to us immediately in writing; the defective parts are to be re-

turned to us on request. The costs for dismounting, mounting, freight and postage will

not be covered by us. Should a complaint prove unjustified, the customer who placed

the order shall pay our costs.

This guarantee is valid only in conjunction with the acknowledged invoice and com-

mences on the day of delivery.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Novoferm K3 VivoPort in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Novoferm K3 VivoPort

Novoferm K3 VivoPort Additional guide - German - 4 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Novoferm K3 VivoPort Manual

Product: