£ Once the process has nished, symbol S7 ashes and symbol S12 is on.
£ Turn the steam/hot water control (g. 1/C) anti-clockwise.
The internal rinsing program starts and will take about one minute, followed by a brief rinsing of the
coffee spout. The symbol S7
ashes and symbol S2 is on.
£ Remove drip tray with used coffee container (g. 1/O and P) and empty both.
£ Reinsert drip tray and used coffee container.
The appliance briey heats up. It is ready for use again when the bean symbols in the display are on.
Attention: Please remove any descaler residues on the casing immediately with a damp cloth.
Manual descaling
If required the descaling program can also be started and run as described above, without the prompt
of symbol S7
.
4.4 Regular cleaning by hand
Tip: Please follow these cleaning instructions as working with foodstuffs demands the highest degree of
cleanliness.
Attention: Never immerse the appliance in water! Do not use abrasive cleaning agents.
£ Empty drip tray and used coffee container regularly (g. 1/O and P). The red oating indicator at
the back of the drip tray (g. 1/Q) shows the tray’s lling level.
£ Only use a soft, damp cloth for cleaning the casing inside and outside.
£ Empty drip tray and used coffee container (g. 1/O and P) at the latest when this is indicated on
the display (only when the appliance is switched on!).
Occasionally use a little soapy water for cleaning.
£ The water tank should be rinsed daily with clear water and then re-lled daily with fresh cool
water.
TIP: Dried milk residue is difcult to remove.
£ Therefore clean the steam/hot water jet/Spumatore, the suction hose regularly.
Attention: From time to time (ideally each time the appliance will not be used for a while, at any rate in
regular intervals!) the steam/hot water jet needs to be completely dismantled and thoroughly cleaned
under running water (g.3). We recommend our special cleaning agent for milk residue NICC 705.
4.5 Cleaning the brew unit
Attention: Remove the brew unit only when the appliance is switched off.
When necessary the brew unit can be removed and cleaned under cold, running water. Never use
any cleaning agent, but clear, cold water only! For hygienic reasons we recommend the removal and
cleaning of the unit thoroughly after each run of the cleaning program (see chapter 4.2).
£ Open and remove the service door on the right of the casing (g. 1/M).
£ Remove the brew unit by pressing the red switch and turning the handle all the way to the left
until it snaps into place (g. 12).
£ Carefully remove the brew unit using the handle.
£ Clean the brew unit under running cold water and let it dry.
£ Reinsert the brew unit carefully and lock by pressing down the red switch and turning the handle
all the way to the right until it snaps into place.
£ Close the service door and in doing so carefully place the pivots at the back of the door into the
notches. Make sure that the door (g. 1/M) completely snaps back into place.
Report Cause Solution
S3
ashes
No beans £ Add beans, restart coffee
making
S12
Rell water pipe system £ Turn steam/hot water control
clockwise
Filter possibly defective £ Remove or replace lter
S1
on
Water tank is empty £ Fill water tank
Water tank is missing or inserted
incorrectly
£ Reinsert water tank
S2
on
Drip tray and/or used coffee
container full
£ Empty drip tray and/or used
coffee container
S2
ashes
Drip tray with used coffee container
missing or tted incorrectly
£ Reinsert drip tray with used
coffee container
S11
on
System cleaning required £ Clean system
(see chapter 4.2)
S7
on
System descaling necessary £ Descale system
(see chapter 4.3)
S6
on
Filter exhausted £ Change lter
(see chapter 4.1)
S13 bar 1 and bar 5
ash alternately
Brew unit tted incorrectly £ Fit brew unit correctly and
snap into place
(see chapter 4.5)
5. System reports
18 19
4. Cleaning and maintenance 5. System reports
