488211
16
Zoom out
Zoom in
Previous page
1/20
Next page
£ Turn the Right rotary knob to “My coffee”
£ Now press the left rotary knob. For a short time, the drink saved under “My coffee” and the set-
tings saved for this will appear in the settings.
Note: You can only change the following settings while the drink saved under “My coffee” and the set-
tings saved for this drink are displayed. After a short time, the display will switch back to “My coffee“.
Then push the left knob again if required.
£ Turn the Left rotary knob to alter the amount of your hot milk (in ml). For drinks with milk, the
proportion of milk to froth and coffee remains unchanged when the volume is altered.
£ Press the Left rotary knob to alter the strength of your coffee. The more beans shown on the
display, the stronger the coffee.
Note: Your machine cannot be programmed to prepare more than one cup or glass of any drink contain-
ing milk. Place your cup or glass centrally under the spout (Fig 5).
£ Begin the preparation process by pressing the Right rotary knob.
Note: If you began preparation too early, or have made a selection error, you can still change some of
the parameters whilst your drink is being prepared. These parameters are shown on the bottom row of
the display. Whilst they are ashing, you still have time to alter them.
£ Turn the Right rotary knob to the required setting.
On the display, the “bean symbol” (aroma) ashes rst, followed by the “ml. indication” (amount of
coffee) in the line below. You are still able to alter these parameters, whilst they are ashing.
£ If you wish to stop preparation of your drink, press the Right rotary knob.
The “Brewing aborted” message then appears on the display.
4.7 Preparing hot water (e.g. for tea)
The standard factory setting for hot water is 150 ml.
“150 ml” will be shown on your display.
£ In the main menu, turn the Right rotary knob to “Water”.
£ Turn the Left rotary knob to change the setting to the amount required (between 20
and 240 ml).
Important note: Check the size of your cups or glasses. Place a cup or glass under the spout.
£ Unless you make any further changes, your machine will use these settings.
£ Begin the preparation process by pressing the Right rotary knob.
Note: If you began preparation too early, or have made a selection error, you can still change some of
the parameters whilst your hot water is being prepared. The “ml. symbol” will be ashing on the bot-
tom row of your display.
£ Turn the Right rotary knob to the required setting.
£ If you wish to stop preparation of your drink, press the Right rotary knob.
4.8 Setting the coffee grinder
WARNING! The coffee grinder must only be reset whilst grinding is in operation!
The grinding operation can be set to match the type of coffee beans used. We recommend that you
always leave the coffee grinder setting on medium.
In order to adjust the coffee grinder setting, proceed as follows:
£ Open the service hatch on the right of the machine housing (Fig 1/L).
The coffee grinding regulator is located at the top and on the right-hand side (Fig 9).
£ Place a cup under the coffee spout (Fig 6).
£ In the main menu, turn the Right rotary knob to “Espresso”.
£ Now press the Right rotary knob.
£ Whilst grinding is in progress, move the regulator to alter the degree of grinding (Fig 9).
On the regulator, the smaller the point, the ner the coffee powder produced. Note the following:
t beans with a lighter roast need more grinding (move the regulator further to the left),
t beans with a darker roast need less grinding (move the regulator further to the right).
You will need to experiment to nd the regulator setting which suits you best.
£ Re-close the service hatch, making sure that the door studs engage in the slots provided. Then press
the door gently home until it clicks into place.
4.9 Using pre-ground coffee
£ Open the lid to the coffee powder chute on the right-hand side of your machine (Fig 1/M).
The messages “Powder ready” and “Only one cup” are alternately toggled on the display.
£ Put in one measuring spoonful of coffee powder and re-close the lid.
The message “Powder ready” appears on the display.
£ Place a cup under the coffee spout (Fig 5).
£ In the main menu, turn the Right rotary knob to select the drink of your choice.
£ Begin the preparation process by pressing the Right rotary knob.
Note: If you began preparation too early, or have made a selection error, you can still change some of
the parameters whilst your drink is being prepared. These parameters are shown on the bottom row of
the display. Whilst they are ashing, you still have time to alter them.
£ Turn the Right rotary knob to the required setting.
You are still able to alter these parameters, whilst they are ashing.
£ If you wish to stop preparation of your drink, press the Right rotary knob.
The “Brewing aborted” message then appears on the display.
Note: If you opened the coffee powder chute accidentally (or if you did not press the Right rotary knob
after putting in the powder), your machine will automatically rinse the coffee spout (Fig 1/E) once the lid
has been re-closed and will again be ready for operation approx. one minute later.
WARNING! The coffee powder chute must not be used as a coffee container! Do not put more than one
portion of powder into the chute. Only use fresh or vacuum-packed powder made from ground coffee
beans. Water-soluble, instant coffee must not be used!
5. Care and maintenance
Caution: Your machine will display cleaning and maintenance requests as a red display text. Respond
to this request by turning the right rotary knob to the respective request (blue display text) and then
press the right rotary knob. Follow the further instructions in the display. See Points 5.1 to 5.5 for more
details.
If you want to start cleaning or maintenance programmes even though no request has appeared, please
follow the same steps described in Points 5.1 to 5.5.
5.1 Rinsing the frothing device
WARNING! Once activated, the rinsing process must not be interrupted!
We recommend that the frothing device be rinsed out on every occasion after preparation of any drink
containing milk. Rinsing MUST be carried out, however, when instructions to that effect appear on
your display. Proceed as follows:
£ Turn the Right rotary knob to “Setting”. Now press the Right rotary knob.
30 31
4. Preparing speciality coffees 4. Preparing speciality coffees / 5. Care and maintenance
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nivona CafeRomatica 767 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nivona CafeRomatica 767 in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Nivona CafeRomatica 767

Nivona CafeRomatica 767 User Manual - German - 21 pages

Nivona CafeRomatica 767 User Manual - Dutch - 20 pages

Nivona CafeRomatica 767 User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info