609460

Nilfisk-ALTO SCRUBTEC R 466 Manual

75
Zoom out
Zoom in
Previous page
1/124
Next page
USER MANUAL
ENGLISH
9098960000(1)2011-04 A SCRUBTEC R 466 - R 471 - R 471C - BOOST
®
R4 13
Battery type setting
Set the electronic board of the machine and the battery charger according to the type of batteries installed (WET or GEL/AGM) as
shown below:
Turn the ignition key (58) to “I” and, in the very fi rst seconds of machine operation, detect the current setting by counting the 5.
number of fl ashes of the battery warning lights (62), as shown in the following table:
SETTING DISPLAY (71)
BATTERY WARNING LIGHT INDICATION
(62)
BATTERY TYPE CHARGING CURRENT
1 4 fl ashes of the red warning light WET
STANDARD2
4 fl ashes of the green warning light GEL-AGM
3
4 fl ashes of the yellow warning light GEL EXIDE
®
type
4
2 fl ashes of the red warning light WET
REDUCED (see note)5
2 fl ashes of the green warning light GEL-AGM
6
2 fl ashes of the yellow warning light GEL EXIDE
®
type
If the setting is to be changed, perform the following procedure.6.
Turn off the machine by turning the ignition key (58) to “0”.7.
Press and hold the switches (63) and (65) at the same time, then turn the ignition key (58) to “I”.8.
Release the switches (63) and (65) at least 5 seconds after starting the machine.9.
Within 3 seconds, shortly press the switch (65) to go to the next setting (1 to 6 in cyclic sequence).10.
NOTE
When performing steps 9 and 10, the settings are shown on the display (71) too, by the code in the table.
NOTE
When using batteries with a capacity lower than 160Ah@5h (in case of doubt, refer to the battery documents), to avoid
battery overheating during charging procedure, use the REDUCED charging current with setting 4, 5 or 6 shown in the
table, according to the type of batteries installed.
NOTE
The battery charger must be set according to the type of batteries.
Battery charging
Charge the batteries (see the procedure in Maintenance chapter).11.
9098960000(1)2011-04 A.indb 139098960000(1)2011-04 A.indb 13 07/04/2011 15:59:1807/04/2011 15:59:18
… 75 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nilfisk-ALTO SCRUBTEC R 466 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nilfisk-ALTO SCRUBTEC R 466 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info