733845

Nikon Nikon Laser Rangefinder Callaway RAZR Manual

31
Zoom out
Zoom in
Previous page
1/35
Next page
60 61
En
Fr
Es
Pt
En
Fr
Es
Pt
1. 『 』- Marca de alvo/irradiação do laser
『』- Mire no alvo. Posicione o alvo no centro do retículo.
『 』- Aparece enquanto o laser está sendo usado para uma medição.
(Este telêmetro a laser não dispõe de uma única função de medição.)
Advertência: Não olhe para dentro das objetivas quando esta marca é
exibida.
2．『 』: exibição do status da distância/medição.
Indica, de forma digital, a distância medida, em metros/jardas. Também indica o
status da medição como "Measurement in progress” (Medição em andamento),
“Measurement unsuccessful” (Medição não foi bem sucedida) ou “Unable to measure" (Incapaz de medir).
<Exemplos de resultados de medição>
(Distância)
Exibição dos resultados: ( ≧100m/jardas) p.ex., 234 metros = 『』
Exibição dos resultados: ( ＜100m/jardas) p.ex., 76,5 jardas = 『』
『』 - Medindo agora
『』 - Falha na medição ou incapaz de medir a distância.
3. 『』Exibição de Unidades:
『』Indica a distância que está sendo medida, em metros.
『』Indica a distância que está sendo medida, em jardas.
4. 『』Indica a condição da pilha. (Ver "Troca da Pilha")
* Embora o LCD seja produzido com o uso da mais avançada tecnologia, é impossível eliminar completamente
a poeira. Geralmente, um LCD exibe na mesma magnificação ou inferior, porém, o LCD desta unidade é
altamente magnificado pela lente ocular. Por conseguinte, ao usar este produto, pode aparecer poeira como
defeito. Isto, no entanto, não afetará a precisão da medição.
Visor interno Resumo Operacional
Cuidado — O uso de controles e ajustes ou a
execução de procedimentos que não aqueles
especificados nestas instruções podem resultar
em exposição a radiações perigosas.
1. Instale uma pilha no compartimento da pilha.
(Ver "Troca da Pilha")
2. Ajuste da dioptria
Ajuste a dioptria para obter uma imagem nítida no
LCD.
Em primeiro lugar, gire o anel de ajuste da
dioptria no sentido anti-horário até que este pare
completamente. Em seguida, ligue a energia para
ativar o LCD quando você olha através do Telêmetro
a Laser Nikon. Gire o anel de ajuste da dioptria no
sentido horário até que o visor entre em foco.
Se a dioptria não for ajustada para corresponder
à sua visão, você pode não conseguir mirar
corretamente no seu objeto.
3. Medição
Antes de medir, certifique-se de confirmar o ajuste
da unidade.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
1. Pressione o botão POWER
para ligar a energia. 2. Mire no alvo.
Imediatamente
após ligar a energia.
(Inicialização)
Em espera. Mira do alvo.
3. Pressione o botão POWER uma vez para iniciar a medição contínua por
8 segundos. (O modo de medição simples não está disponível neste
modelo de telêmetro a laser).
Medição.
4. Por 8 segundos, o visor interno mostra alternadamente o indicador
“distance” (distância) e “fail to measure” (falha na medição). (Marca de
irradiação do laser está piscando).
Falha na medição ou
incapaz de medir a
distância.
Exibe o número
medido (Alvo 1). Exibe o número
medido (Alvo 2).
5. Após a medição contínua, os resultados medidos são exibidos
por 8 segundos e, depois, a energia é desligada. Se você
pressionar o botão POWER quando a energia estiver ligada
(enquanto o visor interno estiver ativo), tem início uma outra
medição de 8 segundos.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target.
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Nikon Nikon Laser Rangefinder Callaway RAZR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Nikon Nikon Laser Rangefinder Callaway RAZR in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 9,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info