Manual Nikon Nikon Laser Rangefinder Callaway iQ (page 35 of 39) (English, French, Portuguese, Spanish)

733846

Zoom out

Zoom in

1/39

68 69

Resumo operacional

4. Medição

 Nota:PressionaremanterpressionadoobotãoPOWERfazcomque

todos os símbolos sejam exibidos no visor LCD interno. Depois

deremoveroseudedodobotãoPOWER,éexibidooúltimo

ajusteusado.(SevocêpressionarbrevementeobotãoPOWER

e remover o dedo, o visor LCD pode exibir o último ajuste

usado sem exibir todos os símbolos. Isto não é uma avaria ou

outro problema.)

Antes de medir, certifique-se de confirmar o ajuste da unidade.

◎: Veja a seção do modo relevante neste manual, quanto aos

ajustes.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

Measurement

1. Press the POWER button for power-on.

(Power turns off 8 seconds after the last

operation.)

Immediately after power-on.

(Initializing)

Stand-by.

3. Press POWER button once to start single measurement.

Measuring.

4. After measurement, “distance” or “fail to measure” indicator are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another single measurement starts.

Failure to measure or

unable to measure distance.

Displays the measured

figure. (Target 1)

Displays the measured

figure. (Target 2)

3. Keep pressing POWER button to start continuous measurement up to 20 seconds. The internal display shows “distance” and

“fail to measure” indicator alternately.

Note: Laser irradiaton mark is blinking during the measurement.

Note: If you stop pressing the button, the continuous measuremen stops

Target focusing.

2. Aim at the target.

Positionthetargetatthecenterofthereticle

[Single measurement]

Failure to measure or

unable to measure distance.

Upward measurement. Downward measurement.

Displays the measured figure.

[Continuous measurement]

4. After continuous measurement, the measure results are displayed for 8 seconds, then power turns off. If you press the POWER

button during power-on (while the internal display is lit), another measrement starts.

1.PressioneobotãoPOWERparaligaraenergia.(Aenergiaé

desligada 8 segundos após a última operação.)

Imediatamente após ligar a

energia(Inicialização)

Em espera.

2.Mirenoalvo.

Posicione o alvo no centro do retículo

Miradoalvo

[Medição simples]

3.PressioneobotãoPOWERumavezparainiciaramedição

simples.

Medição.

4.Apósamedição,osindicadores“distance”(distância)ou“failto

measure”(falhanamedição)sãoexibidosporpor8segundos,e

entãoaenergiaédesligada.SevocêpressionarobotãoPOWER

quandoaenergiaestiverligada(enquantoovisorinternoestiver

iluminado), tem início uma outra medição simples.

Falha na medição

ouincapaz de

medir a distância.

Medição

ascendente.

Medição

descendente.

Exibe o número medido.

[Medição contínua]

3.ContinuepressionandoobotãoPOWERparainiciarumamedição

simples, por até aprox. 5 segundos. O visor interno mostra

alternadamenteoindicador“distance”(distância)e“failtomeasure”(falha

na medição).

Nota: A marca de irradiação de laser fica piscando durante a medição.

Nota:Sevocêparardepressionarobotão,amediçãocontínuapara.

Falha na medição ou

incapaz de medir a

distância.

Exibe o número medido

(Alvo1)

Exibe o número medido

(Alvo2)

4. Após a medição contínua, os resultados medidos são exibidos por 8

segundos,eentãoaenergiaédesligada.SevocêpressionarobotãoPOWER

quandoaenergiaestiverligada(enquantoovisorinternoestiverativo),tem

início uma outra medição.

Pisca enquanto realiza medições.

Ao medir um pino em um campo de golfe, por

exemplo, use o modo de medição Contínuo, para

fácilmedição.Comnenhumobjetoentrevocêea

haste da bandeira, o menor número é a distância

até a sua haste de bandeira alvo.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Nikon Nikon Laser Rangefinder Callaway iQ in the language / languages: English, French, Portuguese, Spanish as an attachment in your email.

The manual is 12,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Nikon Nikon Laser Rangefinder Callaway iQ Manual

Product: