670580
1
Zoom out
Zoom in
Previous page
1/2
Next page
)NSTALLATION'UIDE
DGFV338 ProSafe™ Wireless ADSL Modem VPN Firewall Router
Start Here
Follow these instructions to set up your wireless ADSL gateway. You can also
consult the documentation links on the Resource CD or the NETGEAR knowledgebase at
http://kbserver.netgear.com.
Prepare to Install Your Gateway
The DGFV338 ProSafe Wireless ADSL Modem VPN Firewall Router can be connected
either via an ADSL connection using the internal modem or connected using an Ethernet
connection through an external modem. Either connection is compatible with the wireless
networking bands.
First, Connect the DGFV338
1. CONNECT THE ANTENNAS TO THE DGFV338.
Attach the antennas supplied with the wireless ADSL gateway as shown in (1) and
(2).
2. CONNECT THE CABLES BETWEEN THE DGFV338, THE ISP LINE,
AND A COMPUTER
a. Connect the DGFV338 using one of the following methods:
If you are using a direct ADSL connection, insert the telephone cable
directly into the DSL WAN port (3) of the DGFV338, or
4
5
6
3
2
1
If you are using the Ethernet connection to an external modem, turn off and
unplug the broadband modem. Insert the Ethernet cable from the modem
into the 10/100 WAN port (4) of the DGFV338.
Note: You can connect to both WAN ports if you are planning on using the WAN
rollover feature, but not necessary otherwise.
b. Insert the Ethernet cable that came with your wireless ADSL gateway into a
LAN port on the router (5) and the other end into the Ethernet port of your
computer.
Your network cables are connected and you are ready to restart your network.
3. RESTART YOUR NETWORK IN THE CORRECT SEQUENCE
Warning: Failure to restart your network in the correct sequence could prevent you
from connecting to the Internet.
a. First, power on the broadband modem (if required). Wait two minutes.
b. Now, power on the DGFV338 by connecting the power supply to your gateway
(6). Wait one minute.
c. Last, turn on your computer.
d. Check the DGFV338 status lights to verify the following:
Power: The power light should turn solid green. If it does not turn solid
green, see the Troubleshooting section of the full manual.
Test: When the router is first turned on, the test light is yellow then goes off.
After two minutes if it is still on, see the Troubleshooting Tips below.
WAN: Either the Link/Act light on the 10/100 WAN port or the DSL light
should be lit, depending on the method of connection. If not, make sure the
Ethernet cable is securely attached to the modem and the 10/100 WAN port,
and that the modem is powered on, or that the ADSL line is securely
attached to the gateway and the ADSL outlet.
LOCAL: A LAN light (such as 8) should be lit. Green on top indicates your
computer is communicating at 100 Mbps. If a LAN light is not lit, check that
Power
Test
Internet Ports
Local Port 8
Wireless
the Ethernet cable from the computer to the router is securely attached at
both ends, and that the computer is turned on.
Configure the DGFV338 for Internet Access
Before you begin, be sure you have the configuration parameters from your ISP handy.
1. LOG IN TO THE WIRELESS ADSL GATEWAY
Note: To connect to the firewall, your computer needs to be configured to obtain IP
addresses automatically, which is usually the case.
a. Use a browser to connect to http://192.168.1.1. For security reasons, the firewall
has its own user name and password.
When prompted, enter admin for the firewall User Name and password for the
firewall password.
b. You are now connected to the firewall.
Select Web Support on the main menu for links to the NETGEAR DGFV338
product documentation and support knowledge base. Be aware that the default
configuration login time-out is 5 minutes of inactivity, after which automatic
logout will occur.
2. CONNECT TO THE INTERNET
Configure your ISP connection for Internet access based on your WAN port
connection configuration:
a. From the Network Configuration main menu, select WAN Settings and then
select either the ADSL ISP Settings tab (for DSL) or the Ethernet ISP Settings
(for 10/100)—or configure both if you connected both WAN ports. Click Auto
Detect for the router to detect your ISP connection, or enter the parameters to
complete the Internet configuration.
b. When finished, click Test to verify that the Internet connection you selected is
active.
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear DGFV338 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear DGFV338 in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info