681368

Netgear Arlo FlexPower Base Station VNB4000 Manual

1
Zoom out
Zoom in
Previous page
1/2
Next page
FlexPower Base Station for
FlexPower ONVIF Cameras
Model VNB4000-111PAS
Package Contents
Base station
Power cord
(localized to the region)
Note: For the ceiling and wall installation kit, see the other side of this
document.
Ethernet cable
Step 1: Install the Base Station
1. Use an Ethernet cable to connect the base station to a router or switch.
2. Connect the power cord that came in the package to the base station
and plug it in to an electrical outlet.
3. Press the Power button on the rear of the base station.
After the base station boots, the Power LED and the Network LED light
solid green.
Step 2: Sync Your Cameras to the Base Station
1. Make sure that the rechargeable battery is installed in the camera and
the camera is powered on.
For information about how to install the camera battery, see the quick
start guide that came with the camera.
2. Place the camera 2 to 4 feet (60 to 120 cm) from the base station.
3. On the base station, press the SYNC button.
The camera LED on the base station begins blinking green. This indicates
that the base station is attempting to pair with a camera.
4. On the camera, press the SYNC button.
The camera LED blinks blue. This indicates that the camera is attempting
to pair with the base station.
When the camera is paired to the base station, the camera Sync LED
blinks blue rapidly and then the camera LED on the base station lights
solid green.
5. Repeat Steps 1–4 to pair more cameras to the base station, if desired.
6. Move the cameras to the desired locations.
Step 3: Initial Setup
During initial setup, your computer or mobile device must be connected to
the same LAN as the base station. An Internet connection is not required.
1. Connect your computer or mobile device to the same LAN as the base
station.
If you are unable to connect to the same LAN using WiFi, use an Ethernet
cable to connect a computer to the same router or switch as the base
station.
2. Do one of the following:
• Windows-based computer. Open a folder and then click
Network or Network Places. Look for a FlexPowerBS-xxx
icon. It might appear in the other devices category.
• Mac, Linux, or mobile device. Open a web browser and enter
http://FlexPowerBS-xxx/ (replace xxx with the last 3 digits
of the base station serial number). The serial number is on the
base station label.
• IP address. Use your router’s admin web interface or a
network scan tool to look up the IP address for the base
station and then type the IP address into your browser
address bar.
3. Enter the password.
The default password is password.
4. When prompted, create a new password.
You are prompted to select 60 hz or 50 hz for the flicker setting.
5. Either accept the 60 hz default setting, or select 50 hz.
The home page displays all cameras that are paired to the base station.
To change the camera names, use the Camera Settings menu for each
camera.
To refresh the camera image, tap or click the Snapshot button for each
camera. This is useful when mounting and positioning the camera.
For optimal performance, we recommend that you set up motion detection
sensitivity and a motion detection schedule, as described in the Wire-Free IP
Camera Base Station User Manual.
Installation on a Flat Surface
You can mount the base station on a ceiling or wall, or install it on a flat
surface. For optimal antenna performance, we recommend mounting the
base station on a ceiling or installing it on a flat surface. For information
about how to mount the base station, see the other side of this document.
For installation on flat surface, attach the four round rubber feet to the
locations marked by the gray circles on the bottom of the base station.
The FlexPower Base Station accepts WiFi streaming video data from
FlexPower ONVIF Wire-Free IP Cameras and delivers the video data to ONVIF-
compliant VMS platforms such as Milestone. Each base station supports WiFi
streaming from up to four cameras.
Quick Start Guide
November 2018
©2018 Arlo Technologies, Inc. Arlo, Arlo logo, and Every Angle Covered are trademarks of Arlo
Technologies, Inc. Other trademarks are for reference purposes only.
Compliance
For regulatory compliance information including the EU Declaration of Conformity, visit
www.arlo.com/about/regulatory/.
Arlo Technologies, Inc.
2200 Faraday Ave. Suite 150
Carlsbad, CA 92008 USA
www.arlo.com
www.arlo.com/support
Arlo International, Ltd.
Floor 3, Building 3 University Technology Center
Curraheen Road, Cork, Ireland
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Netgear Arlo FlexPower Base Station VNB4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Netgear Arlo FlexPower Base Station VNB4000 in the language / languages: English as an attachment in your email.

The manual is 1,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info