671550
2
Zoom out
Zoom in
Previous page
1/10
Next page
de
Ø
Montageanleitung
Das müssen Sie beachten
Elektrischer Anschluss: nur durch konzessionierten Fach-
mann. Bei Falschanschluss erlischt die Garantie.
Einbau: nur fachgerecht, bei Schäden haftet der Monteur.
Anschluss: das Gerät entspricht der Schutzklasse I und darf
nur in Verbindung mit Schutzleiteranschluss betrieben werden.
Installation: in der Installation muss ein allpoliger Trennschalter
mit 3 mm Kontaktöffnung vorhanden sein.
Unterbau: keine Kühlgeräte, Geschirrspüler, unbelüftete Backö-
fen, Waschmaschinen unterbauen.
Modular- /Kompakt-Geschirrspüler der gleichen Marke können
untergebaut werden. Arbeitsplattendicke dann mindestens 40
mm.
Wird unter dem Kochfeld ein Backofen eingebaut, kann die
Arbeitsplattendicke von den Maßangaben in dieser Anleitung
abweichen. Beachten Sie die Hinweise in der Montageanleitung
des Backofens.
Zwischenboden: wenn die Kochfeldunterseite berührbar ist,
muss ein Zwischenboden montiert werden.
Fragen Sie im Fachhandel nach einem Zwischenboden als
Zubehör.
Wenn Sie einen eigenen Zwischenboden verwenden, muss der
Mindestabstand zum Netzanschluss des Gerätes 10 mm betra-
gen.
Arbeitsplatte: eben, waagrecht, stabil.
: Träger von elektronischen Implantaten!
Das Gerät kann Permanentmagnete enthalten, die elektronische
Implantate wie z.B. Herzschrittmacher oder Insulinpumpen
beeinflussen können. Deshalb bei der Montage einen Mindest-
abstand von 10 cm zu elektronischen Implantaten einhalten.
Möbel vorbereiten - Bild 1
Einbaumöbel: mindestens 90°C temperaturbeständig.
Ausschnitt: Mindestabstand zu seitlichen Wänden: 90 mm.
Nach Ausschnittarbeiten Späne entfernen.
Schnittflächen: hitzebeständig versiegeln.
Kochfeld anschließen und einsetzen - Bild 2
Vor Geräteanschluss Hausinstallation überprüfen.
A: Gerät mit 3-adriger Anschlussleitung: Farbcodierung der
Netzanschlussleitung: grün-gelb = Schutzleiter
<, blau = (Null)
Neutral-Leiter, braun = Phase (Aussenleiter).
Auf geeignete Absicherung der Hausinatallation achten. Im
Bedarfsfall durch Leitung für mehrphasigen Anschluss ersetz-
ten. Bei Austausch der Leitung siehe B:
B: Gerät ohne vormontierter Anschlussleitung: nur nach
Anschlussbild anschließen. Bei Bedarf beiliegende Kupferbrü-
cken montieren. Netzanschlussleitung: Typ H05 VV-F oder
höherwertig; erforderlichen Adernquerschnitt entspechend der
Strombelastung bestimmen. Ein Querschnitt < 1,5 mm
2
ist nicht
zulässig!
C: Gerät mit vormontierter 5-adriger Anschlussleitung: nur ein
geschulter Kundendienst-Techniker darf die Anschlussleitung
austauschen.
Einsetzen: Anschlussleitung nicht einklemmen, nicht über
scharfe Kanten führen. Bei untergebautem Backofen Leitung an
den hinteren Ecken des Backofens zur Anschlussdose führen.
Hinweis: erscheint im Display des Gerätes
—…‹‹ ist es falsch
angeschlossen. Gerät vom Netz trennen, Anschluss überprüfen.
Geflieste Arbeitsplatten: Fliesenfugen mit Silikonkautschuk
abdichten.
Kochfeld ausbauen: Das Gerät spannungslos machen. Koch-
feld von unten herausdrücken.
Kochfeld einsetzen bei vorhandenem
Arbeitsplattenausschnitt mit 500mm Tiefe - Bild 3
1. Mitte des Ausschnittes markieren
2. Kochfeld aufsetzen
3. Markierungen Kochfeldrahmen und Ausschnitt ausrichten
4. Kochfeld eindrücken.
en
Ú
Installation instructions
The following must be noted
Electrical connection: To be carried out only by a licensed
expert. Incorrect connection will invalidate the warranty.
Installation: To be carried out only by a professional. The fitter
is liable for any damage.
Connection: The appliance fulfils the requirements of protection
class I and may only be operated in conjunction with an earth
conductor.
Installation: An all-pole isolating switch with a contact gap of at
least a 3 mm must be included in the installation.
Under-fitting: Do not install refrigerators, dishwashers, non-
ventilated ovens or washing machines underneath the
appliance.
Modular/compact dishwashers of the same brand can be
installed underneath. The work surface must be at least 40 mm
thick.
If an oven is being installed underneath the hob, the work
surface thickness may differ from the dimensions given in these
instructions. Observe the information in the oven's installation
instructions.
Intermediate floor: If the underside of the hob can be touched,
an intermediate floor must be fitted.
Ask your specialist retailer for an intermediate floor as an
accessory.
If you use your own intermediate floor, the minimum distance to
the appliance's mains connection must be 10 mm.
Work surface: Level, horizontal, stable.
: Wearers of electronic implants!
The appliance may contain permanent magnets which may
affect electronic implants, e.g. heart pacemakers or insulin
pumps. Therefore, during installation, wearers of electronic
implants must maintain a minimum distance of 10 cm from the
appliance.
Preparing the units - Figure 1
Fitting unit: Heat resistant to at least 90°C.
Cut-out: Minimum distance to the side walls: 90 mm.
After the cutting out work is complete, remove the shavings.
Cut surfaces: Seal with heat-resistant material.
Connecting and fitting the hob - Fig. 2
Before connecting the appliance, check the household
installation.
A: Appliance with 3-wire power cable: Colour coding of the
power cord: green-yellow = earth
<, blue = (zero) neutral,
brown = live (external conductor).
Make sure that the household installation has suitable fuse or
circuit breaker protection. If necessary, replace with a cable for
a multiphase connection. When replacing the cable, see B:
B: Appliance without pre-fitted power cable: Only connect in
accordance with the connection diagram. If necessary, fit the
copper bridges supplied. Power cord: Type H05 VV-F or higher;
determine the required wire cross-section depending on the
current rating. A cross-section of < 1.5 mm
2
is not permissible.
C: Appliance with pre-fitted 5-wire power cable: The power
cable must only be replaced by a trained after-sales engineer.
Installing: Do not trap the power cable and do not route it over
sharp edges. If the oven is a built-under type, route the cable on
the rear corners of the oven to the socket.
Note: If
—…‹‹ appears in the display, the appliance has not
been connected correctly. Disconnect the appliance from the
mains and check the connection.
Tiled work surfaces: Seal the tile joints with silicone rubber.
Removing the hob: Disconnect the appliance from the power
supply. Push out the hob from below.
Insert the hob in the existing worktop cut-out with a depth of
500 mm - Figure 3
1. Mark the centre of the cut-out
2. Put the hob in place
3. Align the markings on the hob surround and cut-out
4. Press in the hob.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Neff T16BD56N0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Neff T16BD56N0 in the language / languages: All languages as an attachment in your email.

The manual is 0,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Neff T16BD56N0

Neff T16BD56N0 User Manual - English, German, Dutch, French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info