637928
24
Zoom out
Zoom in
Previous page
1/28
Next page
24
Wall Mounting Instructions:
1. Using the two holes provided in the vertical tube, mount the
bracket to the wall.
2. Ensure minimum clearance to combustibles are maintained, 4”
(100mm) to sides, and 6”(150mm) from the rear.
3. Do not locate the grill under unprotected combustible construction.
4.The platform may be swivelled by removing the two #8 x 3/8”
flathead phillips screws and turning the platform to the desired angle.
Replace the two screws and tighten.
5. Once the platform is located in the desired position, the grill can be
mounted:
a. Lock the lid of the grill closed with the latch.
b. Hold the grill by the handle with one hand, place the other hand under the grill in the
centre of the front tapered surface.
c. Place the grill bottom on the platform and slide it forward to engage the tab protruding from
the bottom of the grill. Ensure that the tab is properly engaged.
d. When the dimples on the bottom of the unit line up with the holes on the platform, the latch is
ready to be fastened.
6. Once the grill has been attached, thread the regulator (clockwise) into the regulator mount.
On tube burner version, lift the burner slightly to align it with the orifice. Tighten by hand.
7. To fasten the regulator locking bracket, locate it at the bottom back corner of the regulator mount and turn the regulator until the
gas inlet is aligned with the hole in the regulator locking bracket. Slide the locking bracket forward until the two tabs engage into the
slots on the regulator mount. Tap in firmly.
8. Attach the cylinder to the regulator by turning clockwise. (Be sure not to cross thread the cylinder.)
Trailer Ball Mounting Instructions:
1. Place the ball mount over the ball on your drawbar or bumper.
2.Tighten the two wing screws until the mount is firmly held in place.
3. Once the mounting arm is tight, the grill can be mounted:
a. Lock the lid of the grill closed with the latch.
b. Hold the grill by the handle with one hand, place the other hand
under the grill in the centre of the front tapered surface.
c. Place the grill bottom on the platform and slide it forward to
engage the tab protruding from the bottom of the grill. Ensure that the
tab is properly engaged.
d. When the dimples on the bottom of the unit line up with the holes on the
platform, the latch is ready to be fastened.
4. Once the grill has been attached, thread the regulator (clockwise) into the regulator
mount. On tube burner version, lift the burner slightly to align it with the orifice. Tighten
by hand.
5. To fasten the regulator locking bracket, locate it at the bottom back corner of the
regulator mount and turn the regulator until the gas inlet is aligned with the hole in the
regulator locking bracket. Slide the locking bracket forward until the two tabs engage into
the slots on the regulator mount. Tap in firmly.
6. Attach the cylinder to the regulator by turning clockwise. (Be sure not to cross thread
the cylinder.)
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Napoleon PTSS215PI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Napoleon PTSS215PI in the language / languages: English, French as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info