493498
44
Zoom out
Zoom in
Previous page
1/48
Next page
The T 187 has the capability to operate via Alternate IR channel. This is
practically useful if you have two NAD products that can be operated by
similar remote control commands. With alternate IR Channel, two dierent
NAD products can be controlled independently in the same zone by
setting each one to a dierent IR channel.
IR CHANNEL ASSIGNMENT
The T 187 and the HTR 8 remote control must be set to the same channel.
To change the Main Zone IR Channel on the T 187
• Press and hold [ a SOURCE ] and then toggle STANDBY button to select
desired IR Channel – the VFD will show “IR Channel 1” or “IR Channel 0”.
The default IR Channel is “IR Channel 0”.
To change the IR Channel on the HTR 8 remote control
• Include a channel number before the library code. For HTR 8, library
code “100” is the default library table for AMP device. To select this
AMP library table for “IR Channel 0”, retain the library code “100” .
• If you want to load the AMP library table on “IR Channel 1”, prex the
library code with “1” to indicate association with “IR Channel 1”. Load
then the AMP library table using the code “1100”.
SAMPLE SETUP OF TWO NAD PRODUCTS ON THE SAME ZONE
NAD T 187 and NAD C 326BEE are both defaulted to IR Channel 0. If [OFF]
button is pressed on the HTR 8 remote control (or SR 8 remote control for
the C 326BEE), both products will go to standby mode. Press [ON] and both
products will power up from standby mode.
To prevent both products from simultaneously going in and out of standby
mode along with other common commands, set each one to a dierent
IR channel. In this setup, we will keep C 326BEE and SR 8 remote control
defaulted to “IR Channel 0”. As for T 187, we will assign it to “IR Channel 1”;
the same applies to HTR 8.
Set T 187 and HTR 8 to “IR Channel 1” via the following procedure.
T 187
• Press and hold [ a SOURCE ] and then toggle STANDBY button to
select “IR Channel 1”.
HTR 8
Begin by ensuring that the T 187 is powered-up (“on, not merely in
standby).
• To enter HTR 8’s library mode, press and hold both the [AMP] device
and [A/V PSET] until the LEARN LED turns green.
• While keeping the HTR 8 pointed towards the T 187, enter the
library code “1100”. Press [OFF]. If the T 187 goes to standby mode,
press [ENTER] to accept the library code number and exit library
mode.
With both T 187 and HTR 8 set to “IR Channel 1”, the C 326BEE can now be
remotely controlled independent of the T 187.
NOTE
Performing a Factory Reset for T 187 or HTR 8 will result to a return to the
factorydefault“IRChannel0”setting.
OPERATION
USING IR CHANNEL
44
ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙ
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD T 187 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD T 187 in the language / languages: English as an attachment in your email.

The manual is 8,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of NAD T 187

NAD T 187 User Manual - German - 48 pages

NAD T 187 User Manual - Dutch - 48 pages

NAD T 187 User Manual - French - 48 pages

NAD T 187 User Manual - Italian - 48 pages

NAD T 187 User Manual - Swedish - 48 pages

NAD T 187 User Manual - Spanish - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info