Manual NAD s 400 (page 5 of 32) (English, German, French, Italian, Portuguese, Swedish, Spanish)

161410

Zoom out

Zoom in

1/32

3. BLEND

High Blend is used for stations that are too remote or weak to permit

noise-free reception in stereo. In order to reduce noise and hiss, this

feature “blends” the stereo channels into mono within a narrow

audio frequency band, thereby reducing hiss considerably while still

maintaining good stereo separation. Pressing BLEND first shows the

status in the display panel. Pressing again within approx. five seconds

changes to ON or OFF.

4. IF

Intermediate Frequency control. Changes the IF between two values,

WIDE for the best possible sound quality and NARROW to remove

interference between stations that are very close to each other in

frequency. Pressing IF first shows the status in the display panel.

Pressing again within approx. five seconds changes to NARROW or

WIDE.

5. ANTENNA

Switches between one of the two antennas that may be connected

to the S400. Pressing ANTENNA first shows the status in the display

panel (Antenna 1 or 2). Pressing again within approx. five seconds

cycles between the two. Simultaneously, the signal strength for the

current antenna is shown as “S” and 0 to 9, where 0 is minimum or

no signal and 9 is maximum signal strength.

6. PRESET (230V VERSION)

OR MODE (120V VERSION)

The PRESET (or MODE) button switches between two ways of using

the TUNE buttons or .

Press the PRESET (or MODE) button until the “PRESET” LED lights up.

Press the button to scroll to a lower number preset. Press the

button to scroll to a higher preset number. A total of 30 preset

memories are available. This is a “wrap-around” function, so that

going from the highest number preset the tuner will go to the

lowest preset number when is pressed.

Refer to section 10. STORING AND RECALLING PRESETS.

NOTE: In the 120V North America version of the S400, which is not

equipped with RDS, the PRESET button is named MODE. It switches

between the Preset and Search functions indicated by the PRESET

and SEARCH LED’s lighting up alternately.

7. LED INDICATORS

The PRESET indicator is explained under section 6. PRESET.

The RDS indicator lights up when a station broadcasting RDS data is

received.

The SEARCH indicator lights up (in 120V version only) when the

S400 is in Search mode.

The STEREO indicator lights up when the S400 receives a stereo

broadcast.

The CENTRE TUNE indicator lights up when the S400 is tuned to the

exact frequency of the transmitter.

8. DOT MATRIX DISPLAY AND DISPLAY BUTTON

The display is the centre of information. It is controlled by the

DISPLAY button, which allows you to read out various details about

the broadcasts.

1. When the S400 is switched on, the display shows the frequency,

the signal strength and the Preset number (if any).

2. After 3 seconds, the display switches to RDS station name and

frequency, or manually entered name. If there is no RDS data or

name, the display remains as a).

3. If the DISPLAY button is pressed, the display shows RADIO TEXT if

the station features this.

4. Pressing the DISPLAY button once more changes back to 1.

5. If the DISPLAY button is pressed and held down, the display will

scroll through the above information followed by all setup details

for Mute, IF, Antenna and Blend. Each line is shown for 2 seconds.

9. STORE

The STORE button is used to store stations into the Preset Memory.

Used in conjunction with the PRESET (or MODE) and TUNE buttons.

10. TUNE AND

The function of these buttons depends on the tuning mode

indicated in the display panel.

In normal operation there are 2 modes:

a) Preset mode Press the PRESET (or MODE) button until the

“PRESET” LED lights up. See section 6. PRESET.

b) Search mode Press the PRESET(or MODE) button until the

“PRESET” LED extinguishes (or in 120V versions, until the SEARCH

LED lights up).

Now you can use the TUNE buttons or to engage

automatic or manual tuning up or down the frequency band.

Auto By keeping one of the TUNE buttons depressed for more than

approx. one second and then letting go, the tuner will search

automatically for the first reasonably strong radio station, where it

will stop. Press and hold the TUNE button again to start searching

again. If a stereo station is received, the “STEREO” LED will light

up.

Manual By tapping one of the TUNE buttons or rapidly,

you can perform manual tuning up or down the frequency band

for precise tuning to a specific frequency. With each successive tap

of the keys, the tuner will take 0.025MHz steps on so you can

accurately tune into the desired frequency. This tuning mode can

also be useful when trying to receive a radio station, which is too

weak for the Search mode.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of NAD s 400 in the language / languages: English, German, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

NAD s 400 Manual

Product: