745051
1
Zoom out
Zoom in
Previous page
1/2
Next page
© NAD CI 16-60
®
CI 16-60 Multi-Channel Amplier
Quick Setup Guide
GUIDELINE FOR NETWORK SETUP CONNECTION
This guideline is applicable to PC, MAC or smartphone control devices. Adapt the guidelines according to your
control device.
1 Use an Ethernet cable (not supplied) to connect CI 16-60’s LAN port to your Wired network or router.
IMPORTANT NOTES
For wired connection to be established, ensure that a broadband router that supports Ethernet is setup and
available.
Ensure that CI 16-60 and the control device (PC, Mac or smartphone device) are connected to the same network.
Use the information in the rear panel MAC ID sticker to identify the CI 16-60 from your network.
2 Power up your CI 16-60. The CI 16-60 will not communicate with the network when in Eco standby mode.
3 Use any network IP scanner to nd your CI 16-60’s Network ID (listed as the product name (NAD CI 16-60)
immediately followed by the last six digits in the MAC (Machine Access Control) address
(example: NAD CI16-60_123456). Note also the corresponding IP address assigned by the network.
4 Type the IP address into your control devices web browser to access your CI 16-60’s User Interface (UI).
5 Congure your CI 16-60’s Identication, Input/Output and Settings parameters via User Interface.
FIRMWARE UPGRADE PROCEDURE
1 Upon gaining access to your CI 16-60’s User Interface, check immediately for any rmware update by selecting
“Check For Updates” from the “Settings” tab.
2 Follow the rmware upgrade prompt instructions to complete the upgrade process.
POWER OPTIONS
SETTING DESCRIPTION
Power button Press power button to set unit to operating or standby mode.
Always On
Unit is always in operating mode. Shut down power by disconnecting unit’s AC plug from the mains power
source.
12V Trigger
Presence or absence of +12V DC supply from compatible devices to rear panel +12V TRIGGER IN will remotely
switch the unit to operating or standby mode.
Signal Sense
Unit will instantaneously turn from standby to operating mode if it senses any input signal (approximately
above 2 mV RMS input) applied through any of the GLOBAL or LINE INPUT sockets.
IMPORTANT
CI 16-60 factory default setting for Eco Mode is ON. With “Power Mode” set to “Signal Sense” and “Eco Mode” set
to “ON”, CI 16-60 will automatically go to Eco standby mode after 20 minutes of no active audio source input.
nadelectronics.com/product/ci-16-60-multi-channel-amplier
support.nadelectronics.com
AUDIO OUT
L
R
© NAD CI 16-60
1.
© NAD CI 16-60
x1
© NAD CI 16-60
2 CHANNEL AUDIO OUT
UNBALANCED
R BALANCED L BALANCED
L
R
x1/x2/x3...x8
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
© NAD CI 16-60
MODEM USBLAN 4
LAN 3LAN 2LAN 1
DISPLAY USB USB
x8 x1 x1 x4 x4
1


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD CI 16-60 DSP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD CI 16-60 DSP in the language / languages: English as an attachment in your email.

The manual is 5,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info