602909
4
Zoom out
Zoom in
Previous page
1/28
Next page
ENGLISH FRANÇAIS
DEUTSCH
ESPAÑOL
ITALIANO
PORTUGUÊS
SVENSKA
This turntable has been engineered to give extremely good musical reproduction. Inherent in the design
are several features that improve sound quality and focus the manufacturing costs where they are most
needed.
Example: Speed change is achieved by manually moving the drive belt from one pulley to another as
shown below.
The cost saving from the use of manual speed change allows a very expensive low vibration motor with
an accuracy exceeding that of conventional designs to be employed.
TIPS AND SUGGESTIONS
1 Try to mount the turntable on a rigid, level surface. A light shelf screwed to the wall or in an alcove
would be ideal. Avoid mounting on hollow or heavy cabinets, or anything mounted on a wooden
floor.
2 Try to keep the lid closed whilst playing records. This will prevent dust falling onto the records and
make cleaning unnecessary. There may also be a sound improvement.
3 Don’t use a record cleaner that works as the record plays, or any cleaners that use water or fluids.
Don’t touch the playing surface of records. Visible dust on the record surface is simply brushed aside
by the stylus, and any that collects there can easily be blown away.
4 Try to leave the turntable running during a record playing session. Switch on before the start, and only
switch off after the last record has finished. Changing records whilst the platter revolves is easier than
it sounds!
5 DO NOT lift the centre hub from its bearing. The bearing is factory assembled with a film of thick
lubricant. Disturbance of this can cause serious problems with speed variation and wear.
6 When switching on the turntable, especially at 45rpm, it is recommended to give the platter a quick
spin clockwise as the ‘ON’ switch is pressed. This relieves strain on the motor and belt.
7 No maintenance should be necessary. If the turntable is working well, leave it alone. Some settling of
the anti-vibration feet may cause the turntable to lean backwards slightly after a few months, but this
is nothing to worry about.
8 Don’t use any polishes on the turntable or lid. To clean or dust, wipe gently with a soft cotton duster
(slightly damp, only if necessary).
9 The tonearm is automatically earthed (or ground) through the arm cable screening. No other earthing
should be necessary.
10 Save the packing, in case the turntable has to be transported in the future.
11 When the record reaches the end of one side, remember to lift the stylus off the surface of the record
using the lift/lower mechanism.
ENJOY THE MUSIC!
33rpm 45rpm
4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for NAD C552 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of NAD C552 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info